Mitsubishi Montero (2004+). Manual — part 369
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-963
TANK
PRS.
SNSR
73
Fuel tank
differential
pressure
sensor
• Ignition switch: "ON"
• Fuel cap removal
−3.3 to 3.3
kPa
(
−0.97 to
0.97 in.Hg)
−
−
TP SNSR
(MAIN)
79
Throttle
position sensor
(main)*
4
• Remove the
intake air
hose at the
throttle body
• Disconnect
the throttle
position
sensor, and
then
connect
terminal
numbers
No. 1, No. 2,
No. 3 and
No. 4 with
the use of
the special
tool:
MB991658.
• Ignition
switch: ON
Fully close the
throttle valve
with your finger
200
− 800
mV
Code No.
P0122,
P0123
Fully open the
throttle valve
with your finger
3,800
−
4,900 mV
No load
450
−
1,000 mV
A/C switch: "OFF"
→ "ON"
Voltage
rises
• A/C switch: "OFF"
• Shift lever: "N" → "D"
TP
LEARN
MID
9A
Throttle
position sensor
(main)
mid opening
learning value
Ignition switch: ON
500
−
2,000 mV
Code No.
P0122,
P0123
MUT-III
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPEC-
TION
PROCE-
DURE NO.
REFE-
RENCE
PAGE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-964
TP SNSR
(SUB)
14
Throttle
position sensor
(sub)*
4
• Remove the
intake air
hose at the
throttle body
• Disconnect
the throttle
position
sensor, and
then
connect
terminal
numbers
No. 1, No. 2,
No. 3 and
No. 4 with
the use of
the special
tool:
MB991658.
• Ignition
switch: ON
Fully close the
throttle valve
with your finger
2,200
−
2,800 mV
Code No.
P0222,
P0223
Fully open the
throttle valve
with your finger
3,800
−
4,900 mV
MUT-III
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPEC-
TION
PROCE-
DURE NO.
REFE-
RENCE
PAGE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-965
TP SNSR 8A*
5
Throttle
position sensor
(main)*
4
• Remove the
intake air
hose at the
throttle body
• Disconnect
the throttle
position
sensor, and
then
connect
terminal
numbers
No. 1, No. 2,
No. 3 and
No. 4 with
the use of
the special
MB991658
tool.
• Ignition
switch: ON
Fully close the
throttle valve
with your finger
0
− 10 %
Code No.
P0122,
P0123
Fully open the
throttle valve
with your finger
80
− 100 %
No load
450
−
1,000 mV
A/C switch: "OFF"
→ "ON"
Voltage
rises
• A/C switch: "OFF"
• Shift lever: "N" → "D"
VAF
RESET
SIG
34
Volume airflow
sensor reset
signal
Engine:
warming up
Engine is idling ON
−
−
2,500 r/min
OFF
VAF
SENSOR
12
Volume airflow
sensor*
1
• Engine
coolant
temperature
: 80
− 95°C
(176
−
203
°F)
• Lights,
electric
cooling fan
and all
accessories
: "OFF"*
6
• Transmission
: "P" range
Engine is idling 17
− 43 HZ −
−
2,500 r/min
64
− 104
Hz
Engine is
revved
Frequency
(or air flow
volume)
increases
in
response
to revving
MUT-III
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPEC-
TION
PROCE-
DURE NO.
REFE-
RENCE
PAGE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-966
ACTUATOR TEST REFERENCE TABLE
M1131152500569
NOTE: *: Continues for 27 minutes. Can be released
by pressing the CLEAR key.
VAF
SENSOR
12*
5
Volume airflow
sensor (mass
airflow rate)*
1
• Engine
coolant
temperature
: 80
− 95°C
(176
−
203
°F)
• Lights,
electric
cooling fan
and all
accessories
: "OFF"*
6
• Transmission
: "P" range
Engine is idling 3.5
− 7.5
gm/s
−
−
2,500 r/min
13.6
− 19.6
gm/s)
Engine is
revved
Frequency
(or air flow
volume)
increases
in
response
to revving
VSS
24*
5
Vehicle speed
signal
Drive at 40 km/h (25 mph).
Approxi-
mately 40
km/h (25
mph)
−
−
MUT-III
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPEC-
TION
PROCE-
DURE NO.
REFE-
RENCE
PAGE
MUT-III
SCAN
TOOL
DIS-
PLAY
ITEM
NO.
INSPEC-
TION ITEM
DRIVE
CONTENTS
INSPECTION
REQUIREMENT
NORMAL
CONDITION
INSPEC-
TION
PROCEDU
RE NO.
REFERENCE
PAGE
BASIC
TIMING
17*
Basic
ignition
timing
Set to ignition
timing
adjustment
mode
• Engine: idling
• Connect timing light
5
°BTDC
−
−
EVAP
PURG
SOL
08
Evaporativ
e emission
purge
solenoid
Solenoid valve
turns from
OFF to ON.
Ignition switch: "ON"
Clicks when
solenoid valve
is driven.
Code No.
P0443
EVAP
VENT
29
Evaporativ
e emission
ventila-
tion
solenoid
Solenoid valve
turns from
OFF to ON.
Ignition switch: "ON"
Clicks when
solenoid valve
is driven.
Code No.
P0446
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст