Mitsubishi Montero (2004+). Manual — part 488
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-23
DTC 14: TPMS Abnormality (Vehicle Speed Signal)
JUNCTION BLOCK
JUNCTION
BLOCK
VEHICLE
SPEED
SENSOR
JOINT
CONNECTOR (4)
IGNITION
SWITCH (IG1)
TPMS
RECEIVER
Vehicle Speed Sensor Circuit
AC204171
CONNECTORS: D-112, D-116
D-112
D-116
BF
AC204173
CONNECTOR : D-220
BP
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-24
.
CIRCUIT OPERATION
The TPMS receiver monitors the vehicle speed sig-
nal.
.
TPMS DTC SET CONDITION
DTC 14 will be set if the TPMS receiver does not
receive vehicle speed signal of 5 km/h (3 mph) or
more during driving. At the same time this DTC is
set, the TPMS warning light flashes. TPMS receiver
senses the vehicle’s driving state by a roll switch
inside the TPMS transmitter.
.
TROUBLESHOOTING HINTS (THE MOST LIKELY
CAUSES FOR THIS DTC TO SET ARE:)
• Malfunction of the vehicle speed sensor
• Damaged wiring harness or connector
• Malfunction of the TPMS receiver
.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
.
STEP 1. Check A/T diagnostic trouble code.
Q: Is A/T DTC 29 (vehicle speed sensor system) set?
YES : Carry out troubleshooting for A/T DTC 29 (vehicle
speed sensor system) (Refer to GROUP 23A,
Diagnostic Trouble Code Procedures
NO : Go to Step 2.
AC308263
AB
CONNECTOR: E-111
AC307592
G-28
CONNECTOR: G-28
AD
THIRD SEAT
BELT (RH)
TPMS RECEIVER
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-25
STEP 2. Check the following connectors.
• Joint connector D-116
• Intermediate connector E-111
• Junction block connector D-220
Check the connectors for loose, corroded or damaged termi-
nals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 3.
NO : Repair it. And then go to Step 7.
AC204171
CONNECTOR : D-116
AN
9 10
8
6 7
31 32
30
29
18 19 20 21
5
4
2
1
3
27
26
24
23
25
12 13 14 15 16 17
28
11
22
33
AC308263
AC
CONNECTOR: E-111
AC204173
CONNECTOR : D-220
BQ
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-26
STEP 3. Check the following harness wire.
• The wire between joint connector D-116 (terminal 23) and
junction block connector D-220 (terminal 5)
Q: Is the harness wire damaged?
YES : Repair or replace it. And then go to Step 7.
NO : Go to Step 4.
STEP 4. Check the following connectors.
• Intermediate connector D-112
• TPMS receiver connector G-28
Check the connectors for loose, corroded or damaged termi-
nals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 5.
NO : Repair it. And then go to Step 7.
AC204171
CONNECTOR : D-116
AN
9 10
8
6 7
31 32
30
29
18 19 20 21
5
4
2
1
3
27
26
24
23
25
12 13 14 15 16 17
28
11
22
33
AC204173
CONNECTOR : D-220
AI
HARNESS SIDE
1
2
3
7
8
6
5
10
4
9
AC204171 AL
CONNECTOR : D-112
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
AC307592 AE
CONNECTOR : G-28
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст