Mitsubishi Montero (2004+). Manual — part 334
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-823
.
CIRCUIT OPERATION
• A 5-volt voltage is supplied to the barometric
pressure sensor power terminal (terminal No. 1)
from the PCM (terminal No. 97). The ground ter-
minal (terminal No. 5) is grounded with PCM (ter-
minal No. 88).
• A voltage that is proportional to the atmospheric
pressure is sent to the PCM (terminal No. 100)
from the barometric pressure sensor output ter-
minal (terminal No. 2).
.
TECHNICAL DESCRIPTION
• The barometric pressure sensor outputs a volt-
age which corresponds to the barometric pres-
sure.
• The PCM checks whether this voltage is within a
specified range.
.
DESCRIPTIONS OF MONITOR METHODS
Barometric pressure sensor output voltage is out of
reasonable barometric pressure range.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
AK200940
BAROMETRIC
PRESSURE
SENSOR
AB
CONNECTOR: B-48
B-48(B)
AK201038AK
CONNECTORS: D-134, D-135
PCM
D-134(GR) D-135(GR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-824
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 2 seconds or more have passed since the start-
ing sequence was completed.
• Battery positive voltage is higher than 8 volts.
Judgement Criteria
• Barometric pressure sensor output signal has
continued to be approximately 112.8 kPa (33.3
in.Hg) or higher (approximately 4,000 ft below
sea level) for 10 seconds.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Procedure 6
.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are: )
• Barometric pressure sensor failed.
• Open barometric pressure sensor circuit, harness
damage, or connector damage.
• PCM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991911: Main Harness B
START
END
NO
NO
NO
YES
YES
YES
MALFUNCTION
GOOD
NO
YES
AK302969
MONITORING
CONDITIONS
BAROMETRIC PRESSURE
< 49.5kPa (14.6in.Hg)
BAROMETRIC PRESSURE
> 112.8kPa (33.3in.Hg)
CONTINUOUS
FAILURE FOR 10secs
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-825
STEP 1. Using scan tool MB991958, check data list item 25:
Barometric Pressure Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item
25, Barometric Pressure Sensor.
• When altitude is 0 m (0 foot), 101 kPa (29.8 in.Hg.).
• When altitude is 600 m (1,969 feet), 95 kPa (28.1
in.Hg.).
• When altitude is 1,200 m (3,937 feet), 88 kPa (26.0
in.Hg.).
• When altitude is 1,800 m (5,906 feet), 81 kPa (23.9
in.Hg.).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
NO : Go to Step 2.
STEP 2. Measure the sensor output voltage at barometric
pressure sensor connector B-48 by backprobing.
(1) Do not disconnect the connector B-48.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 2 and ground by
backprobing.
• When altitude is 0 m (0 foot), voltage should be 3.7 and
4.3 volts.
• When altitude is 600 m (1,969 feet), voltage should be
3.4 and 4.0 volts.
• When altitude is 1,200 m (3,937 feet), voltage should be
3.2 and 3.8 volts.
• When altitude is 1,800 m (5,906 feet), voltage should be
2.9 and 3.5 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 3.
NO : Go to Step 5.
AK302970
AB
MB991911
MB991824
MB991827
AK200937
3
4
5
1
2
6
7
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-48
B-48(B)
AKX01520
6 7
1 2 3 4 5
AKX01520AK
B-48 HARNESS
CONNECTOR:
HARNESS SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-826
STEP 3. Check connector B-48 at the barometric pressure
sensor and connector D-135 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
STEP 4. Using scan tool MB991958, check data list item 25:
Barometric Pressure Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item
25, Barometric Pressure Sensor.
• When altitude is 0 m (0 foot), 101 kPa (29.8 in.Hg.).
• When altitude is 600 m (1,969 feet), 95 kPa (28.1
in.Hg.).
• When altitude is 1,200 m (3,937 feet), 88 kPa (26.0
in.Hg.).
• When altitude is 1,800 m (5,906 feet), 81 kPa (23.9
in.Hg.).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
NO : Replace the PCM. Then go to Step 12.
AK200937
3
4
5
1
2
6
7
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-48
B-48(B)
AK200947
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CONNECTOR: D-135
HARNESS CONNECTOR:
COMPONENT SIDE
AB
PCM
D-135(GR)
AK302970
AB
MB991911
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст