Mitsubishi Montero (2004+). Manual — part 267
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-555
STEP 7. Check connector D-132 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 8.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
STEP 8. Check for open circuit and short circuit to ground
between evaporative emission ventilation solenoid
connector G-27 (terminal No. 1) and PCM connector D-132
(terminal No. 11).
AK200938
2
3
4
5
6
7
8
9
1
10
14
15
16
17
18
19
20
21
22
23
24
25
26
27
11
12
13
AB
CONNECTOR: D-132
HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-132(GR)
AK200969
1
2
G-27(B)
AB
CONNECTOR: G-27
HARNESS
CONNECTOR:
COMPONENT SIDE
AK200938
2
3
4
5
6
7
8
9
1
10
14
15
16
17
18
19
20
21
22
23
24
25
26
27
11
12
13
AB
CONNECTOR: D-132
HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-132(GR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-556
NOTE: Check harness after checking intermediate connectors
F-10, D-112 and E-113. If intermediate connectors are dam-
aged, repair or replace them. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 12.
NO : Repair it. Then go to Step 12.
STEP 9. Check connector D-132 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
STEP 10. Check for harness damage between MFI relay
connector B-22X (terminal No. 1) and evaporative emission
ventilation solenoid connector G-27 (terminal No. 2).
AK200938
2
3
4
5
6
7
8
9
1
10
14
15
16
17
18
19
20
21
22
23
24
25
26
27
11
12
13
AB
CONNECTOR: D-132
HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-132(GR)
AK200951
2 1
3
4
B-22X
AB
CONNECTOR: B-22X
HARNESS
CONNECTOR:
COMPONENT SIDE
AK200969
1
2
G-27(B)
AB
CONNECTOR: G-27
HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-557
NOTE: Check harness after checking intermediate connectors
D-116, E-111, D-112 and F-10. If intermediate connectors are
damaged, repair or replace them. Refer to GROUP 00E, Har-
ness Connector Inspection
. Then go to Step 12.
Q: Is the harness wire in good condition?
YES : Go to Step 11.
NO : Repair it. Then go to Step 12.
STEP 11. Check for harness damage between evaporative
emission ventilation solenoid connector G-27 (terminal No.
1) and PCM connector D-132 (terminal No. 11).
NOTE: Check harness after checking intermediate connectors
F-10, D-112 and E-113. If intermediate connectors are dam-
aged, repair or replace them. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 12.
NO : Repair it. Then go to Step 12.
AK200969
1
2
G-27(B)
AB
CONNECTOR: G-27
HARNESS
CONNECTOR:
COMPONENT SIDE
AK200938
2
3
4
5
6
7
8
9
1
10
14
15
16
17
18
19
20
21
22
23
24
25
26
27
11
12
13
AB
CONNECTOR: D-132
HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-132(GR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-558
STEP 12. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
Other Monitor
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0446 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
DTC P0451: Evaporative Emission System Pressure Sensor Range/Performance
AC203991
SYSTEM DIAGRAM
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Q
S
R
P
FUEL TANK
CHECK VALVE B
CHECK VALVE A
EVAPORATIVE
EMISSION
PURGE
SOLENOID
EVAPORATIVE EMISSION
VENTILATION SOLENOID
EVAPORATIVE
EMISSION
CANISTER
VENT PIPE
ASSEMBLY
AC
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
ONBOARD REFUELING
VAPOR RECOVERY(ORVR)
VENT VALVE MODULE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст