Mitsubishi Montero (2004+). Manual — part 540
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-129
STEP 3. Check the wiring harness between radio and CD
player connector D-06 (terminal 11) and the battery.
NOTE: After inspecting intermediate connector D-28, inspect
the wire. If intermediate connector D-28 is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector Inspec-
tion
.
Q: Is the wiring harness between radio and CD player
connector D-06 (terminal 11) and battery in good
condition?
YES : Go to Step 4.
NO : Repair the wiring harness. If the power switch is
turned on, the radio and CD player should operate
normally.
STEP 4. Check the installation condition of the radio and
CD player.
NOTE: The radio and CD player are grounded to the instru-
ment panel center reinforcement directly.
Q: Are the radio and CD player installed correctly?
YES : Repair or replace the radio and CD player. If the
power switch is turned on, the radio and CD player
should operate normally.
NO : Install the radio and CD player properly. If the power
switch is turned on, the radio and CD player should
operate normally.
AC204188
CONNECTORS: D-06, D-28
D-28
D-06
BK
D-28
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
D-06
1
7
2
8
10
11
5
13
6
14
12
4
9
3
HARNESS SIDE
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-130
STEP 5. Measure at radio and CD player connector D-06 in
order to check the battery circuit of power supply system
to the radio and CD player (ignition switch ACC).
(1) Disconnect radio and CD player connector D-06, and
measure at the wiring harness side.
(2) Turn the ignition switch to "ACC" position.
(3) Measure the voltage between terminal 10 and ground by
backprobing.
• The voltage should equal approximately 12 volts (bat-
tery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 8.
NO : Go to Step 6.
STEP 6. Check radio and CD player connector D-06 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are radio and CD player connector D-06 in good
condition?
YES : Go to Step 7.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. If the power switch is turned on, the radio
and CD player should operate normally.
AC204170
CONNECTOR : D-06
CS
HARNESS SIDE
1
7
2
8
10
11
5
13
6
14
12
4
9
3
AC204738 DR
HARNESS SIDE: D-06
6
14
4 5
13
11
3
9 10
2
8
1
7
12
AC204170
CONNECTOR : D-06
CS
HARNESS SIDE
1
7
2
8
10
11
5
13
6
14
12
4
9
3
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-131
STEP 7. Check the wiring harness between radio and CD
player connector D-06 (terminal 10) and ignition switch
(ACC).
NOTE: Also check intermediate connector D-28, junction block
connector D-208 and D-221. If intermediate connector D-28,
junction block connector D-208 and D-221 is damaged, repair
or replace the connector as described in GROUP 00E, Harness
Connector Inspection
.
Q: Is the wiring harness between radio and CD player
connector D-06 (terminal 10) and ignition switch (ACC)
in good condition?
YES : There is no action to be taken.
NO : Repair the wiring harness. If the power switch is
turned on, the radio and CD player should operate
normally.
AC204188
CONNECTORS: D-06, D-28
D-28
D-06
BK
D-28
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
D-06
1
7
2
8
10
11
5
13
6
14
12
4
9
3
HARNESS SIDE
AC204191
CONNECTORS : D-208, D-221
D-208
D-208
HARNESS SIDE
HARNESS SIDE
D-221
D-221
AQ
1
2
3
5
6
4
3
1
4
6 5
7
8
2
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-132
STEP 8. Check the installation condition of the radio and
CD player.
NOTE: The radio and CD player are grounded to the instru-
ment panel center reinforcement directly.
Q: Are the radio and CD player installed correctly?
YES : Repair or replace the radio and CD player. If the
power switch is turned on, the radio and CD player
should operate normally.
NO : Install the radio and CD player properly. If the power
switch is turned on, the radio and CD player should
operate normally.
INSPECTION PROCEDURE 2: No Sound. <Vehicles with Amplifier>
29
FUSIBLE
LINK
RADIO AND CD PLAYER
DIN CABLE
AMPLIFIER
Amplifier Power Supply Circuit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст