Mitsubishi Montero (2004+). Manual — part 805
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-477
STEP 1. Use scan tool MB991958 to select "ECU COMM
CHK" on the SWS monitor display.
Check the ETACS-ECU.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect the special tool. Refer to "How to connect SWS
monitor
.
(2) Turn the ignition switch to the "LOCK" (OFF) position.
(3) Operate scan tool MB991958 according to the procedure
below to display "ECU COMM CHK."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "ECU COMM CHK."
(4) Scan tool MB991958 should show "OK" on the "ECU
COMM CHK" menu for the "ETACS ECU" menu.
Q: Is "OK" displayed on the "ETACS ECU" menu?
YES : Go to Step 2.
NO : Refer to Inspection Procedure A-3 "Communication
with the ETACS-ECU is not possible
."
STEP 2. Check ETACS-ECU connector D-224 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connector D-224 in good condition?
YES : Go to Step 3.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. The theft-alarm indicator light should
illuminate, and the theft-alarm system should be set
normally.
AC309091
MB991911
MB991827
MB991824
AB
MB991806
MB991862
DATA LINK
CONNECTOR
(16-PIN)
DATA LINK
CONNECTOR
(13-PIN)
AC204174
CONNECTOR : D-224
AD
D-224(B)
D-224(B)
HARNESS SIDE
21
23
24
22
32
3433
31
26
27
28
3029
38
39
40
36
37
25
35
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-478
STEP 3. Check at ETACS-ECU connector D-224 in order to
check the theft-alarm indicator light circuit.
(1) Disconnect ETACS-ECU connector D-224, and measure at
the wiring harness side.
(2) The theft-alarm indicator light should illuminate when
terminal 40 is grounded.
Q: Does the theft-alarm indicator light illuminate?
YES : Go to Step 9.
NO : Go to Step 4.
STEP 4. Check theft-alarm indicator light connector D-105
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is theft-alarm indicator light connector D-105 in good
condition?
YES : Go to Step 5.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. The theft-alarm indicator light should
illuminate, and the theft-alarm system should be set
normally.
AC204174
CONNECTOR : D-224
AD
D-224(B)
D-224(B)
HARNESS SIDE
21
23
24
22
32
3433
31
26
27
28
3029
38
39
40
36
37
25
35
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
AC100319AB
CONNECTOR D-224
(HARNESS SIDE)
AC204170
CONNECTOR : D-105
AL
HARNESS
SIDE
D-105(B)
D-105(B)
1
2
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-479
STEP 5. Check the theft-alarm indicator light.
(1) Remove the RV meter. Refer to GROUP 54A, RV meter
(2) Disconnect theft-alarm indicator light connector D-105.
(3) The theft-alarm indicator light should illuminate when
battery voltage is applied between terminals 1 and 2.
Q: Does the theft-alarm indicator light illuminate?
YES : Go to Step 6.
NO : Replace the theft-alarm indicator light. The theft-alarm
indicator light should illuminate, and the theft-alarm
system should be set normally.
STEP 6. Check the fusible link (1) line of power supply
circuit to the theft-alarm indicator light circuit. Test at
theft-alarm indicator light connector D-105.
(1) Disconnect theft-alarm indicator light connector D-105 and
measure the voltage available at the wiring harness side of
the connector.
(2) Measure the voltage between terminal 2 and ground.
• The voltage should be approximately 12 volts (battery
positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 8.
NO : Go to Step 7.
AC204170
CONNECTOR : D-105
AL
HARNESS
SIDE
D-105(B)
D-105(B)
1
2
ACX02296
AC204170
CONNECTOR : D-105
AL
HARNESS
SIDE
D-105(B)
D-105(B)
1
2
AC100067
1
2
AB
CONNECTOR D-105
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-480
STEP 7. Check the wiring harness between theft-alarm
indicator light connector D-105 (terminal 1) and the fusible
link (1).
NOTE: Also check intermediate connector D-28 and joint con-
nector D-02 for loose, corroded, or damaged terminals, or ter-
minals pushed back in the connector. If intermediate connector
D-28 or joint connector D-02 is damaged, repair or replace the
damaged component(s) as described in GROUP 00E, Harness
Connector Inspection
.
Q: Is the wiring harness between theft-alarm indicator
light connector D-105 (terminal 1) and the fusible link (1)
in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. The
theft-alarm indicator light should illuminate, and the
theft-alarm system should be set normally.
ACX02274
FUSIBLE LINK (1)
AE
BATTERY
AC204170
CONNECTOR : D-105
AL
HARNESS
SIDE
D-105(B)
D-105(B)
1
2
AC204188
CONNECTORS: D-02, D-28
D-02
D-02
D-28
AB
D-28
9 10
8
6 7
31 32
30
29
18 19 20 21
5
4
2
1
3
27
26
24
23
25
12 13 14 15 16 17
28
11
22
33
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст