Mitsubishi Montero (2004+). Manual — part 451
SPECIAL TOOLS
TSB Revision
FRONT AXLE
26-9
STEP 4. Check the oil level.
Remove the filler plug and check the gear oil level.
Q: Is the gear oil level more than 8 mm (0.3 inch) below the
bottom of the filler plug hole?
YES : Check the oil leakage from differential carrier, and
repair if necessary. Then, refill Hypoid gear oil API
classification GL-5 or higher; Above
−23°C(−10°F):
SAE 90, 85W-90, 80W-90, From
−34 to −23°C(−30 to
−10°F): SAE 80W, 80W-90, Below −34°C(−30°F):
SAE 75W. Then go to Step 5.
NO : There is no action to be taken.
STEP 5. Retest the system.
Q: Is there oil leakage?
YES : Repeat from Step 1.
NO : The procedure is complete.
SPECIAL TOOLS
M1261000600438
AC000439
UPPER LIMIT
LOWER LIMIT
AB
8 mm (0.3 in)
TOOLS
TOOL NUMBER
AND NAME
SUPERSESSION APPLICATION
MB990925
Bearing and oil
seal installer set
MB990925-01 or
General service
tool
• Press-fitting of wheel bearing outer
race MB990935 MB990938
• Press-fitting of oil seal (differential
carrier)
• Press-fitting of drive pinion rear
bearing outer race MB990934
MB990938
• Press-fitting of drive pinion front
bearing outer race MB990936
MB990938
• Oil seal installation (free wheel
clutch) MB990926 MB990938
MB990590
Rear axle shaft
oil seal remover
A: MB990212
Adapter
B: MB990211
Sliding
hammer
−
• Removal of differential carrier oil seal
• Removal and installation of inner
shaft (Used together with
MB990906)
MB990767
End yoke holder
MB990767-01
Hub fixing
MB990925
MB990590
A
B
B990767
SPECIAL TOOLS
TSB Revision
FRONT AXLE
26-10
MB991897
Ball joint
remover
MB990635-01,
MB991113-01 or
General service
tool
Knuckle and tie rod end ball joint
disconnection
NOTE: Steering linkage puller
(MB990635 or MB991113)is also used
to disconnect knuckle and tie rod end
ball joint.
MB990998
Front hub
remover and
installer
MB990998-01 or
General service
tool
Inspection of hub rotation starting
torque
MB990326
Preload socket
General service
tool
• Inspection of hub rotation starting
torque
• Measurement of wheel bearing
turning torque
MB991561
Boot band
crimping tool
MB991561
Resin boot band installation
MB990906
Driveshaft
attachment
MB990241-01
Removal and installation of inner shaft
(Used together with MB990211)
MB990560
Bearing remover
MD998348-01
• Removal and press-fitting of inner
shaft bearing
• Removal of freewheel clutch bearing
MB990955
Oil seal installer
MB990955-01
Press-fitting of housing tube dust seal
(Used together with MB990938)
MB991168
Differential oil
seal installer
−
Installation of freewheel clutch oil seal
TOOLS
TOOL NUMBER
AND NAME
SUPERSESSION APPLICATION
AC106827
MB990998
MB990326
MB991561
MB990906
MB990560
MB990955
MB991168
SPECIAL TOOLS
TSB Revision
FRONT AXLE
26-11
MB990799
Ball joint
Remover and
installer
MB990799-01
Installation of freewheel clutch bearing
MB990890 or
MB990891
Rear suspension
bushing base
MB990890-01
MB990909
Working base
−
Supporting of front differential carrier
assembly
MB991116
Adapter
−
Supporting of front differential carrier
assembly
MB990810
Side bearing
puller
MB990810-01
• Remove of side bearing inner race
• Remove of companion flange
MB990811
Differential side
bearing cap
MB990811-01
MB990850
End yoke holder
MB990850-01
Removal and installation of companion
flange
TOOLS
TOOL NUMBER
AND NAME
SUPERSESSION APPLICATION
MB990799
MB990890
MB990909
MB990810
MB990811
MB990850
SPECIAL TOOLS
TSB Revision
FRONT AXLE
26-12
MB990339
Bearing puller
MB990339-01
Removal of drive pinion front bearing
inner race
MB990648
Bearing remover
MB990648-01
MB990685
Torque wrench
−
• Inspection of hub rotation starting
torque
• Measurement of wheel bearing
turning torque
MB991171
Pinion height
gauge set
A: MB990819
Drive pinion
gauge
assembly
B: MB991170
Cylinder
gauge
−
• Inspection of drive pinion rotation
starting torque
• Measurement of drive pinion height
MB990802
Bearing installer
MB990802-01
• Press-fitting of drive pinion front
bearing inner race
• Press-fitting of side bearing inner
race
MB990031 or
MB990699
Drive pinion oil
seal installer
MB990031-01
Press-fitting of drive pinion oil seal
MB990813
Tap
−
Removal of adhesive
TOOLS
TOOL NUMBER
AND NAME
SUPERSESSION APPLICATION
MB990339
MB990648
MB990802
MB990031
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст