Mitsubishi Montero (2004+). Manual — part 496
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-55
INSPECTION PROCEDURE 2: The TPMS Warning Light Flashes.
.
CIRCUIT OPERATION
• The TPMS warning light will flash when a fault
has occurred in the TPMS.
• The TPMS warning light may also flash when a
fault has occurred in the TPMS warning light sig-
nal circuit (including open circuit and shorted cir-
cuit).
.
COMBINATION
METER
TPMS
RECEIVER
TPMS Warning Light Signal Circuit
AC204170
CONNECTOR: D-04
EI
D-04 (GR)
AC204171
CONNECTOR : D-112
AU
AC307592
G-28
CONNECTOR: G-28
AD
THIRD SEAT
BELT (RH)
TPMS RECEIVER
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-56
TECHNICAL DESCRIPTION (COMMENT)
• If any TPMS DTCs are set, carry out the relevant
troubleshooting.
• If no TPMS DTC is set, carry out the trouble-
shooting for the TPMS warning light signal circuit.
.
TROUBLESHOOTING HINTS (THE MOST LIKELY
CAUSES FOR THIS CASE:)
• A fault has occurred in the TPMS.
• Damaged harness wire or connector in the TPMS
warning light signal circuit
• Malfunction of the combination meter
• Malfunction of the TPMS receiver
.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
.
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check whether any TPMS DTC is set.
Q: Is any TPMS DTC set?
YES : Carry out the relevant TPMS troubleshooting (Refer
to
NO : Go to Step 2.
AC306409AF
MB991911
MB991824
MB991827
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-57
STEP 2. Check the following connectors.
• Combination meter connector D-04
• Intermediate connector D-112
• TPMS receiver connector G-28
Check the connectors for loose, corroded or damaged termi-
nals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 3.
NO : Repair it. Then go to Step 5.
AC204170
CONNECTOR: D-04
EL
D-04
COMBINATION METER
CONNECTOR
D-04 (GR)
AC204171 AL
CONNECTOR : D-112
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
AC307592 AE
CONNECTOR : G-28
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-58
STEP 3. Check the following harness wire.
• The wire between combination meter connector D-04 (ter-
minal 41) and TPMS receiver connector G-28 (terminal 7)
Q: Is the harness wire damaged?
YES : Repair or replace it. Then go to Step 5.
NO : Go to Step 4.
STEP 4. Check the combination meter.
Check that the combination meter warning lights and indicators
other than TPMS warning light illuminate normally.
Q: Are there any faults on the combination meter?
YES : Replace the meter assembly (Refer to
).
Then go to Step 5.
NO : Replace the TPMS receiver (Refer to
) and
execute "Tire Pressure Sensor ID Registration" on
scan tool MB991958 "Special Function" (Refer to
). Then go to Step 5.
STEP 5. Retest the system.
Q: Turn the ignition switch to the "ON" position. Does the
TPMS warning light illuminate for three seconds, and
then go out?
YES : The procedure is complete.
NO : Repeat the troubleshooting from Step 1.
AC204170
CONNECTOR : D-04
AD
D-04(GR)
HARNESS
SIDE
D-04(GR)
31
32
41 40
33
34
36
37
35
43
46 45 44
39
42
38
47
AC307592
G-28
AF
G-28
10
5
6
7
9 8
3
4
2 1
HARNESS CONNECTOR:
COMPONENT SIDE
CONNECTOR: G-28
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст