Mitsubishi Montero (2004+). Manual — part 841
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-621
NOTE: Also check intermediate connectors D-111, G-10 and
junction block connector D-217 for loose, corroded, or dam-
aged terminals, or terminals pushed back in the connector. If
intermediate connector D-111, G-10 or junction block connector
D-217 is damaged, Repair or replace the damaged compo-
nent(s) as described in GROUP 00E, Harness Connector
Inspection
.
Q: Is the wiring harness between rear wiper motor
connector I-07 (terminal 3) and ETACS-ECU connector
D-222 (terminal 5) in good condition?
YES : Replace the ETACS-ECU. If the rear wiper operates
normally, it indicates that a correct auto-stop signal is
sent from the rear wiper motor.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. If the rear
wiper operates normally, it indicates that a correct
auto-stop signal is sent from the rear wiper motor.
AC204171
CONNECTOR : D-111
BH
9
8
6 7
5
3 4
20
32
21
33
43
17 18
30
41
16
29
28
39 40
13
25
12
24
35 36
14
26
37
15
27
38
19
31
42
1
10
22
2
11
23
34
AC204173
CONNECTOR : D-217
AG
HARNESS SIDE
8
1
11 10
3
4
12
9
2
13
14
6 5
15
7
D-217
AC204179
CONNECTOR : G-10
AD
4
10
8
7
3
9
5
1
6
2
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-622
INSPECTION PROCEDURE P-9: ETACS-ECU does not receive any signal from hood switch.
.
CIRCUIT OPERATION
The ETACS-ECU operates the theft-alarm system
according to signal from the hood switch.
.
TECHNICAL DESCRIPTION (COMMENT)
If the signal is not normal, the theft-alarm system
does not work normally.
.
TROUBLESHOOTING HINTS
• The hood switch may be defective
• The ETACS-ECU may be defective
Hood Switch Input Circuit
AC204167
CONNECTOR : A-14
A-14(B)
AL
AC204170
CONNECTOR : D-27
BA
AC204174
CONNECTOR : D-223
D-223(B)
AF
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-623
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
STEP 1. Check hood switch connector A-14 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is hood switch connector A-14 in good condition?
YES : Go to Step 2.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. If the theft-alarm system operates normally,
it indicates that a correct signal is sent from the hood
switch.
STEP 2. Check the hood switch.
Remove the hood switch. Then check continuity between the
switch terminals.
Q: Is the hood switch in good condition?
YES : Go to Step 3.
NO : Replace the hood switch. If the theft-alarm system
operates normally, it indicates that a correct signal is
sent from the hood switch.
AC204167
CONNECTOR : A-14
HARNESS
SIDE
A-14(B)
A-14(B)
AC
1
2
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Released
1
− 2
Less than 2 ohms
Pressed
1
− 2
Open circuit
1
2
ACX02415
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-624
STEP 3. Check the ground circuit to the hood switch. Test
at hood switch connector A-14.
(1) Disconnect hood switch connector A-14 and measure the
resistance available at the wiring harness side of the
connector.
(2) Measure the resistance value between terminal 2 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 5.
NO : Go to Step 4.
STEP 4. Check the wiring harness between hood switch
connector A-14 (terminal 2) and ground.
Q: Is the wiring harness between hood switch connector
A-14 (terminal 2) and the ground in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. If the
theft-alarm system operates normally, it indicates that
a correct signal is sent from the hood switch.
AC204167
CONNECTOR : A-14
HARNESS
SIDE
A-14(B)
A-14(B)
AC
1
2
2 1
ACX01608AB
CONNECTOR A-14
(HARNESS SIDE)
AC204167
CONNECTOR : A-14
HARNESS
SIDE
A-14(B)
A-14(B)
AC
1
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст