Mitsubishi Montero (2004+). Manual — part 1063
ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-95
STEP 2 Check the ABS warning light bulb.
(1) Remove the combination meter (Refer to GROUP 54A,
Combination Meter
).
(2) Check the ABS warning light bulb.
Q: Is the bulb burned out?
YES : Replace the bulb and then go to Step 10.
NO : Go to Step 3.
STEP 3. Check the ABS warning light circuit at
M-ASTC-ECU connector E-120.
(1) Disconnect M-ASTC-ECU connector E-120 and measure at
the harness side.
(2) Ground the terminal 62.
(3) Turn the ignition switch to the "ON" position. The ABS
warning light should turn on.
Q: Is the ABS warning light turn on?
YES : Replace the M-ASTC-ECU and then go to Step 5.
NO : Go to Step 4.
AC203901
AC204627
CONNECTOR: E-120
AS
E-120
HARNESS CONNECTOR:
COMPONENT SIDE
ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-96
STEP 4. Check the harness wires between combination
meter connector D-03 terminal 56 and M-ASTC-ECU
connector E-120 terminal 62.
NOTE: After inspecting combination meter connector D-03,
intermediate connector E-110 and M-ASTC-ECU connector
E-120, inspect the wire. If combination meter connector D-03,
intermediate connector E-110 and M-ASTC-ECU connector
E-120 are damaged, repair or replace them. Refer to GROUP
00E, Harness Connector Inspection
.Then go to Step
AC204690 AC
CONNECTOR: D-03
D-03 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
D-03
AC203901
AC204627AG
CONNECTOR: E-120
E-120
HARNESS CONNECTOR:
COMPONENT SIDE
E-120
ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-97
Q: Is the harness wire between combination meter
connector D-03 terminal 56 and M-ASTC-ECU connector
E-120 terminal 62 damaged?
YES : Repair it and then go to Step 10.
NO : Replace the combination meter (printed circuit board)
and go to Step 10.
AC204385
CONNECTOR: E-110
AD
E-110
6
1
7
2
9
8
10
3
5
12
11
4
1314
ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-98
STEP 5. Check the harness wire between combination
meter connector D-03 terminal 56 and valve relay
connector B-21X terminal 2.
NOTE: After inspecting valve relay connector B-21X and inter-
mediate connector E-110, inspect the wire. If valve relay con-
nector B-21X and intermediate connector E-110 are damaged,
repair or replace them. Refer to GROUP 00E, Harness Con-
nector Inspection
.Then go to Step 10.
Q: Is the harness wire between combination meter
connector D-03 terminal 56 and valve relay connector
B-21X terminal 2 damaged?
YES : Repair them and then go to Step 10.
NO : Go to Step 6.
AC204690 AC
CONNECTOR: D-03
D-03 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
D-03
AC204706
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
5
B-21X
CONNECTOR: B-21X
AB
RELAY BOX CONNECTOR
AC204385
CONNECTOR: E-110
AD
E-110
6
1
7
2
9
8
10
3
5
12
11
4
1314
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст