Mitsubishi Montero (2004+). Manual — part 298
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-679
STEP 8. Measure the power supply voltage at PCM harness
side connector D-136.
(1) Disconnect the connector D-136 and measure at the
harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 132 and ground.
• Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 11.
NO : Go to Step 9.
AK201170
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
CONNECTOR: D-136
PCM
D-136(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AB
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
AK201448
AB
D-136 HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-680
STEP 9. Check for open circuit and short circuit to ground
between throttle actuator control motor relay connector
B-23X (terminal No. 1) and PCM connector D-136 (terminal
No. 132).
Q: Is the harness wire in good condition?
YES : Go to Step 10.
NO : Repair it. Then go to Step 17.
AK201172
2 1
3
4
B-23X
AB
CONNECTOR: B-23X
HARNESS
CONNECTOR:
COMPONENT SIDE
AK201170
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
CONNECTOR: D-136
PCM
D-136(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AB
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-681
STEP 10. Check for harness damage between MFI relay
connector B-22X (terminal No. 1) and throttle actuator
control motor relay connector B-23X (terminal No. 4).
Q: Is the harness wire in good condition?
YES : Repair harness wire between throttle actuator control
motor relay connector B-23X (terminal No. 2) and
PCM connector D-132 (terminal No. 15) because of
harness damage. Then go to Step 17.
NO : Repair it. Then go to Step 17.
STEP 11. Check connector D-132 and D-136 at PCM for
damage.
Q: Is the connector in good condition?
YES : Go to Step 12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 17.
AK200951
2 1
3
4
B-22X
AB
CONNECTOR: B-22X
HARNESS
CONNECTOR:
COMPONENT SIDE
AK201172
2 1
3
4
B-23X
AB
CONNECTOR: B-23X
HARNESS
CONNECTOR:
COMPONENT SIDE
2
3
4
5
6
7
8
9
1
10
14
15
16
17
18
19
20
21
22
23
24
25
26
27
11
12
13
AK201566
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
CONNECTORS: D-132, D-136
D-132 HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-132(GR) D-136(GR)
AB
D-136 HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-682
STEP 12. Check the throttle actuator control motor.
(1) Disconnect the connector B-05.
(2) Measure the resistance between throttle actuator control
motor side connector terminal No. 5 and No. 6.
Standard value: 0.3
− 100 ohms
Q: Is the measured resistance between 0.3 and 100 ohms?
YES : Go to Step 13.
NO : Replace the throttle body ASSY. Then go to Step 17.
STEP 13. Check connector B-05 at throttle actuator control
motor for damage.
Q: Is the connector in good condition?
YES : Go to Step 14.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 17.
AK201174
1
6 5 4 3 2
B-05(B)
CONNECTOR: B-05
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
6
1 2 3 4 5
AK201513AB
THROTTLE ACTUATOR
CONTROL MOTOR
SIDE CONNECTOR
AK201174
1
6 5 4 3 2
B-05(B)
CONNECTOR: B-05
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст