Mitsubishi Montero (2004+). Manual — part 753
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-269
STEP 4. Check the battery power supply circuit to the rear
wiper motor. Test at rear wiper motor connector I-07.
(1) Disconnect rear wiper motor connector I-07 and measure
the voltage available at the harness side of the connector.
(2) Turn the rear wiper switch to the "ON" position.
(3) Measure the voltage between terminal 2 and ground.
• The voltage should be approximately 12 volts (battery
positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 8.
NO : Go to Step 5.
STEP 5. Check the ETACS-ECU connector D-222 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is and ETACS-ECU connector D-222 in good condition?
YES : Go to Step 6.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the rear wiper works normally.
ACX02293
CONNECTOR: I-07
AR
I-07(B)
I-07(B)
(HARNESS SIDE)
1
2
3
4
AC204312 AE
CONNECTOR I-07
(HARNESS SIDE)
4 3 2 1
AC203853
CONNECTOR: D-222
AC
JUNCTION BLOCK (REAR VIEW)
D-222
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-270
STEP 6. Check the harness wires between rear wiper
motor connector I-07 (terminal 2) and ETACS-ECU
connector D-222 (terminal 1).
AC203853
CONNECTOR: D-222
AC
JUNCTION BLOCK (REAR VIEW)
D-222
(HARNESS SIDE)
ACX02293
CONNECTOR: I-07
AR
I-07(B)
I-07(B)
(HARNESS SIDE)
1
2
3
4
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-271
NOTE: Also check intermediate connectors G-10, D-111 and
junction block connector D-217. If intermediate connectors
G-10, D-111 or junction block connector D-217 are damaged,
repair or replace damaged component(s) as described in
GROUP 00E, Harness Connector Inspection
Q: Are the harness wires between rear wiper motor
connector I-07 (terminal 2) and ETACS-ECU connector
D-222 (terminal 1) in good condition?
YES : Go to step 7.
NO : The wiring harness may be damaged or the
connectors may have loose, corroded or damaged
terminals or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the rear wiper works normally.
AC203860AC
D-111
CONNECTOR: D-111
D-111
AC203850
CONNECTOR: D-217
AH
D-217
JUNCTION BLOCK
(FRONT VIEW)
D-217
1
8 9 10 11
13 14 15
12
2 3 4
5 6 7
AC204524
CONNECTOR: G-10
AC
G-10
G-10
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-272
STEP 7. Check the rear wiper motor.
(1) Disconnect the rear wiper motor connector I-07.
(2) Connect a battery to the wiper motor as shown in the
illustration and inspect the motor operation.
Q: Is the rear wiper motor in good condition?
YES : No action is necessary and testing is complete.
NO : Replace the rear wiper motor. Verify that the rear
wiper works normally.
STEP 8. Check the ground circuit to the rear wiper motor.
Test at rear wiper motor connector I-07.
(1) Disconnect rear wiper motor connector I-07 and measure
the resistance available at the harness side of the
connector.
(2) Measure the resistance value between terminal 1 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 7.
NO : Go to Step 9.
1 2 3 4
ACX02409AB
I-07
ACX02293
CONNECTOR: I-07
AR
I-07(B)
I-07(B)
(HARNESS SIDE)
1
2
3
4
4 3 2 1
ACX01579AB
CONNECTOR I-07
(HARNESS SIDE)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст