Mitsubishi Montero (2004+). Manual — part 784
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-393
STEP 20. Check the rear turn-signal light bulb (RH).
(1) Remove the rear turn-signal (RH) light bulb.
(2) Verify that the rear turn-signal light bulb (RH) is not
damaged or burned out.
Q: Is the rear turn-signal (RH) light bulb in good condition?
YES : Go to Step 21.
NO : Replace the rear turn-signal (RH) light bulb. Verify
that the turn-signal lights illuminate normally.
STEP 21. Check rear combination light (RH) connector
G-09 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is rear combination light (RH) connector G-09 in good
condition?
YES : Go to Step 22.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the turn-signal lights illuminate
normally.
STEP 22. Check the ground circuit to the rear combination
light (RH). Test at rear combination light (RH) connector
G-09.
(1) Disconnect rear combination light (RH) connector G-09 and
measure the resistance available at the wiring harness side
of the connector.
(2) Measure the resistance value between terminal 4 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 24.
NO : Go to Step 23.
AC204179
CONNECTOR : G-09
AC
HARNESS SIDE
G-09(B)
G-09(B)
1
4
2
3
5
6
AC204179
CONNECTOR : G-09
AC
HARNESS SIDE
G-09(B)
G-09(B)
1
4
2
3
5
6
AC100256
1
4
2
3
5
6
AC
CONNECTOR G-09
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-394
STEP 23. Check the wiring harness between rear
combination light (RH) connector G-09 (terminal 4) and
ground.
Q: Is the wiring harness between rear combination light
(RH) connector G-09 (terminal 4) and ground in good
condition?
YES : Replace the socket assembly. Verify that the
turn-signal lights illuminate normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the turn-signal lights illuminate normally.
STEP 24. Check ETACS-ECU connector D-222 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connector D-222 in good condition?
YES : Go to Step 25.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the turn-signal lights illuminate
normally.
AC204179
CONNECTOR : G-09
AC
HARNESS SIDE
G-09(B)
G-09(B)
1
4
2
3
5
6
AC204174
CONNECTOR : D-222
AB
1
2
3
5
6
4
9 8
121110
13
15 14
16
17
7
19
20
18
JUNCTION BLOCK SIDE
D-222
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-395
STEP 25. Check the wiring harness between rear
combination light (RH) connector G-09 (terminal 5) and
ETACS-ECU connector D-222 (terminal 14).
NOTE: Also check junction block connector D-217 and inter-
mediate connector D-111 for loose, corroded, or damaged ter-
minals, or terminals pushed back in the connector. If junction
block connector D-217 or intermediate connector D-111 is dam-
aged, repair or replace the damaged component(s) as
described in GROUP 00E, Harness Connector Inspection
.
Q: Is the wiring harness between rear combination light
(RH) connector G-09 (terminal 5) and ETACS-ECU
connector D-222 (terminal 14) in good condition?
YES : Replace the socket assembly. Verify that the
turn-signal lights illuminate normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the turn-signal lights illuminate normally.
AC204174
CONNECTOR : D-222
AB
1
2
3
5
6
4
9 8
121110
13
15 14
16
17
7
19
20
18
JUNCTION BLOCK SIDE
D-222
AC204179
CONNECTOR : G-09
AC
HARNESS SIDE
G-09(B)
G-09(B)
1
4
2
3
5
6
AC204171
CONNECTOR : D-111
BH
9
8
6 7
5
3 4
20
32
21
33
43
17 18
30
41
16
29
28
39 40
13
25
12
24
35 36
14
26
37
15
27
38
19
31
42
1
10
22
2
11
23
34
AC204173
CONNECTOR : D-217
AG
HARNESS SIDE
8
1
11 10
3
4
12
9
2
13
14
6 5
15
7
D-217
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-396
STEP 26. Check combination meter connector D-03 and
ETACS-ECU connector D-222 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are combination meter connector D-03 and ETACS-ECU
connector D-222 in good condition?
YES : Go to Step 27.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the turn-signal lights illuminate
normally.
STEP 27. Check the wiring harness between combination
meter connector D-03 (terminal 60) and ETACS-ECU
connector D-222 (terminal 15).
AC204170
CONNECTOR : D-03
AC
D-03(GR)
HARNESS
SIDE
51
52
61 60
53
54
56
57
55
63
66 65 64
59
62
58
67
D-03(GR)
AC204174
CONNECTOR : D-222
AB
1
2
3
5
6
4
9 8
121110
13
15 14
16
17
7
19
20
18
JUNCTION BLOCK SIDE
D-222
AC204170
CONNECTOR : D-03
AC
D-03(GR)
HARNESS
SIDE
51
52
61 60
53
54
56
57
55
63
66 65 64
59
62
58
67
D-03(GR)
AC204174
CONNECTOR : D-222
AB
1
2
3
5
6
4
9 8
121110
13
15 14
16
17
7
19
20
18
JUNCTION BLOCK SIDE
D-222
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст