Mitsubishi Montero (2004+). Manual — part 602
REAR AIR CONDITIONING DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-51
NOTE: Also check intermediate connector D-112. If intermedi-
ate connector D-112 is damaged, repair or replace the connec-
tor as described in GROUP 00E, Harness Connector
Inspection
.
Q: Is the wiring harness between rear cooler unit
connector G-13 (terminal 1, 4 and 3) and rear cooler
control unit connector E-09 (terminal 1, 8 and 12) in
good condition?
YES : Check that the rear air conditioning works normally.
NO : Repair the wiring harness. Check that the rear air
conditioning works normally.
AC204171 AL
CONNECTOR : D-112
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
REAR AIR CONDITIONING DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-52
INSPECTION PROCEDURE 4: Rear Air Conditioning Outlet Air Temperature does not Increase
<Vehicles with Rear A/C>
Air Mixing Damper Control Motor, Air Thermo Sensor and Magnetic Valve Circuit
REAR AIR CONDITIONING DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-53
AC204170
CONNECTORS : D-01, D-30
CZ
D-01
D-30
AC204171
CONNECTOR : D-112
AU
AC204173
CONNECTORS : D-208, D-210
BF
D-208
D-210
AC204176
CONNECTORS : E-06, E-12, E-20
BL
E-20
E-06
E-12
AC204175
CONNECTOR : E-22
AK
AC204179
CONNECTORS : G-24, G-26
BA
G-24
G-26
AC204698 AU
G-26-1
G-26-2
CONNECTORS : G-26-1, G-26-2,
G-26-3, G-26-4
G-26-3
G-26-4
REAR AIR CONDITIONING DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-54
DIAGNOSIS
STEP 1. Check the rear A/C switch (temperature control
switch).
Connect the tester between the connector terminal number 3
and number 5, between the terminal number 5 and number 13
and make sure that the resistance value changes slowly within
the standard value.
Standard value: 0
− 3 kΩ
Q: Is the check result normal?
YES : Go to Step 2.
NO : Replace the rear air-conditioner switch.
STEP 2. Measure the resistance at rear A/C control unit
connector E-20.
(1) Disconnect rear A/C control unit connector E-20, and
measure at the wiring harness side.
(2) Turn the rear fan switch to the "ON" position.
(3) Turn the Rear fan control switch to the "OFF" position.
(4) Measure the resistance between terminal 13 and ground.
• The measured value should be 2 ohms or less.
Q: Does the measured resistance value correspond with
this range?
YES : Go to Step 5.
NO : Go to Step 3.
AC205161
1
7
2
8
10 11
5
13
6
14
12
4
9
3
AC204176
CONNECTOR : E-20
AY
HARNESS SIDE
7
8
3
10 9
2
4
11
1312
5
14
6
1
AC204738
7
8
3
10 9
2
4
11
1312
5
14
6
1
CH
HARNESS SIDE : E-20
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст