Mitsubishi Montero (2004+). Manual — part 781
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-381
INSPECTION PROCEDURE K-3: Frasher timer: One of the turn-signal light do not illuminate.
ETACS-
ECU
FRONT TURN
SIGNAL LIGHT
(LH)
(RH)
REAR COMBINATION
LIGHT
TURN-SIGNAL
LIGHT
(LH)
(RH)
JOINT
CONNECTOR (8)
JOINT
CONNECTOR (1)
COMBINATION
METER
JUNCTION
BLOCK
TURN-SIGNAL
LIGHT RELAY
: LH
TURN-SIGNAL
LIGHT RELAY
: RH
Turn-Signal Lights Circuit
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-382
.
TECHNICAL DESCRIPTION (COMMENT)
If the right or left turn-signal light does not illuminate,
their bulb may be defective.
.
TROUBLESHOOTING HINTS
• The turn-signal light bulb may be defective
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
.
AC204167
CONNECTORS : A-16, A-19
A-16
AR
A-19(B)
AC204166
CONNECTOR : A-35
AN
A-35(B)
AC204170
CONNECTORS : D-03,D-04,D-28,D-30,D-125
BM
D-03(GR)
D-04(GR)
D-125
D-28
D-30
AC204171
CONNECTOR : D-111
AG
AC204173
CONNECTORS : D-210, D-212, D-217
D-210
D-217
D-212
AV
AC204174
CONNECTOR : D-222
AE
AC204179
CONNECTOR : G-19
AM
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-383
DIAGNOSIS
Required Special Tool:
• MB991223: Test Harness Set
STEP 1. Verify the hazard warning light.
Q: Which turn-signal light does not illuminate?
Front turn-signal light (LH) : Go to Step 2.
Front turn-signal light (RH) : Go to Step 8.
Rear combination light (LH) : Go to Step 14.
Rear combination light (RH) : Go to Step 20.
Combination meter (LH) : Go to Step 26.
Combination meter (RH) : Go to Step 28.
Combination meter (both RH and LH) : Go to Step 30.
Front turn-signal light (LH) and combination meter (LH)
:
Go to Step 32.
LH side only : Refer to Inspection Procedure K-1
"Turn-signal lights does not flash when the turn-signal
light switch is turned on
."
RH side only : Refer to Inspection Procedure K-1
"Turn-signal lights does not flash when the turn-signal
light switch is turned on
."
Both LH and RH sides : Refer to Inspection Procedure K-2
"Hazard warning light does not illuminate
STEP 2. Check the front turn-signal light bulb (LH).
(1) Remove the front turn-signal (LH) light bulb.
(2) Verify that the front turn-signal light bulb (LH) is not
damaged or burned out.
Q: Is the front turn-signal (LH) light bulb in good
condition?
YES : Go to Step 3.
NO : Replace the front turn-signal (LH) light bulb. Verify
that the turn-signal lights illuminate normally.
STEP 3. Check front turn-signal light (LH) connector A-19
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is the front turn-signal light (LH) connector A-19 in good
condition?
YES : Go to Step 4.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the turn-signal lights illuminate
normally.
AC204167
CONNECTOR : A-19
HARNESS
SIDE
A-19(B)
A-19(B)
AH
1
2
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-384
STEP 4. Check the ground circuit to the front combination
light (LH). Test at front combination light (LH) connector
A-19.
(1) Disconnect front combination light (LH) connector A-19 and
measure the resistance available at the wiring harness side
of the connector.
(2) Measure the resistance value between terminal 2 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 6.
NO : Go to Step 5.
STEP 5. Check the wiring harness between front
turn-signal light (LH) connector A-19 (terminal 2) and
ground.
Q: Is the wiring harness between front turn-signal light
(LH) connector A-19 (terminal 2) and ground in good
condition?
YES : Replace the socket. Verify that the turn-signal lights
illuminate normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the turn-signal lights illuminate normally.
AC204167
CONNECTOR : A-19
HARNESS
SIDE
A-19(B)
A-19(B)
AH
1
2
AC204786
1
2
AB
CONNECTOR A-19
(HARNESS SIDE)
AC204167
CONNECTOR : A-19
HARNESS
SIDE
A-19(B)
A-19(B)
AH
1
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст