Mitsubishi Montero (2004+). Manual — part 1216

SRS AIR BAG DIAGNOSIS

TSB Revision

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-199

STEP 2. Check the communication line between the
SRS-ECU and the scan tool.
(1) Disconnect SRS-ECU connector E-08 and data link

connector D-118 and measure at the wiring harness side.

CAUTION

Do not insert a test probe into the terminal of the SRS-ECU
connector E-08 from its front side directly as the connector
contact pressure may be weakened.
(2) Check for continuity between the following terminals.

Between connector E-08 terminal 20 and connector D-118
terminal 7
It should be less than 2 ohms.

Q: Does continuity exist?

YES : Go to Step 3.
NO : Go to Step 5.

ACX01478AM

CONNECTOR: E-08

E-08 (Y)

HARNESS SIDE
CONNECTOR
(REAR VIEW)

AC204695

CONNECTOR : D-118

AC

D-118 (B)

ACCELLATOR PEDAL

1 2 3 4 5 6 7 8
9 10 11121314 15 16

D-118
CONNECTOR
(FRONT VIEW)

1314151617181920

5 6 7 8 9 101112

1 2

3 4

1 2 3 4 5 6 7 8

9 10111213141516

AC006263

D-118
CONNECTOR
(FRONT VIEW)

E-08 HARNESS SIDE
CONNECTOR
(REAR VIEW)

AL

SRS AIR BAG DIAGNOSIS

TSB Revision

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-200

STEP 3. Check the ground circuit to the SRS-ECU.
(1) Disconnect SRS-ECU connector E-08, and measure at the

wiring harness side.

CAUTION

Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.

(2) Check for continuity between E-08 harness terminal 7 and

body ground.
It should be less than 2 ohms.

Q: Does continuity exist?

YES : Go to Step 4.
NO : Go to Step 6.

STEP 4. Check the power supply circuit to the SRS-ECU.
(1) Disconnect SRS-ECU connector E-08, and measure at the

wiring harness side.

(2) Connect the negative battery terminal.
(3) Turn the ignition switch to the "ON" position.

CAUTION

Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(4) Measure the voltage between terminals 13, 16 and body

ground.
Voltage should measure 9 volts or more.

Q: Is the measured voltage within the specified range?

YES : Recheck the trouble symptom. If it is not solved,

replace the SRS-ECU (Refer to

P.52B-215

). Then go

to Step 8.

NO : Go to Step 7.

ACX01478AM

CONNECTOR: E-08

E-08 (Y)

HARNESS SIDE
CONNECTOR
(REAR VIEW)

AC201527

9 10 11 12

13 1415 16

1 2

3 4

5 6 7 8

17 18 19 20

E-08 HARNES SIDE
CONNECTOR
(REAR VIEW)

AK

ACX01478AM

CONNECTOR: E-08

E-08 (Y)

HARNESS SIDE
CONNECTOR
(REAR VIEW)

AC006265

13 14 15 16 17 18 19 20

5 6 7 8 9 10 11 12

1 2

3 4

AQ

E-08 HARNESS SIDE
CONNECTOR
(REAR VIEW)

SRS AIR BAG DIAGNOSIS

TSB Revision

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-201

STEP 5. Check the harness wires between SRS-ECU
connector E-08 (terminal No.20) and data link connector
D-118 (terminal No.7).

NOTE: After inspecting intermediate connector D-29 inspect
the wiring harness. If the intermediate connector D-29 is dam-
aged, repair or replace it (Refer to GROUP 00E, Harness Con-
nector Inspection

P.00E-2

).. Then go to Step 8.

Q: Are the harness wires between SRS-ECU connector

E-08 (terminal No.20) and data link connector D-118
(terminal No.7) in good condition?
YES : Go to step 8.
NO : Repair the harness wires between SRS-ECU

connector E-08 and data link connector D-118. Then
go to Step 8.

ACX01478AM

CONNECTOR: E-08

E-08 (Y)

HARNESS SIDE
CONNECTOR
(REAR VIEW)

AC204695

CONNECTOR : D-118

AC

D-118 (B)

ACCELLATOR PEDAL

1 2 3 4 5 6 7 8
9 10 11121314 15 16

D-118
CONNECTOR
(FRONT VIEW)

AC204231AF

CONNECTOR : D-29

D-29

D-29

33

22

11

28

17

16

15

14

13

12

25

23 24

26 27

3

1 2

4 5

21

20

19

18
29 30

32

31

7

6

8

10

9

SRS AIR BAG DIAGNOSIS

TSB Revision

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-202

STEP 6. Check the harness wire between SRS-ECU
connector E-08 (terminal No.7) and ground.
Q: Is the harness wire between SRS-ECU connector E-08

(terminal No.7) and ground in good condition?
YES : Go to Step 8.
NO : Repair the harness wire between SRS-ECU

connector E-08 and ground. Then go to Step 8.

STEP 7. Check the harness wires between SRS-ECU
connector E-08 (terminal No.13 and 16) and ignition switch
connector D-204 (terminal No.2).

ACX01478AM

CONNECTOR: E-08

E-08 (Y)

HARNESS SIDE
CONNECTOR
(REAR VIEW)

ACX01508

GROUND

AE

ACX01478AM

CONNECTOR: E-08

E-08 (Y)

HARNESS SIDE
CONNECTOR
(REAR VIEW)

AC204226AG

CLOCK SPRING

CONNECTOR: D-204

D-204

HARNESS
SIDE
CONNECTOR
(FRONT VIEW)

2
5

6

3

4

1