Mitsubishi Montero (2004+). Manual — part 493
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-43
STEP 12. Check the feeder cable core wire for continuity.
(1) Disconnect the following connectors.
• TPMS antenna (rear-LH) connector G-28-8
• TPMS receiver connector G-28-3
(2) Check the feeder cable core wire for continuity as below.
• The cable between TPMS antenna (rear-LH) connector
G-28-8 (terminal 1) and TPMS receiver connector
G-28-3 (terminal 1)
Q: Is there continuity between the feeder cable core wire?
YES : Replace the TPMS antenna (rear-LH) (Refer to
). And then go to Step 16.
NO : Replace the feeder cable. And then go to Step 17.
AC308265
CONNECTOR: G-28-8
AE
G-28-8 (GR)
AC308264
AC307575
CONNECTOR: G-28-3
AE
TPMS RECEIVER
G-28-3 (GR)
(BLUE TAPING)
AC308266
G-28-8 (GR)
CONNECTORS: G-28-3, G-28-8
AG
FEEDER CABLE
CONNECTOR:
COMPONENT SIDE
G-28-3 G-28-8
G-28-3 (GR)
(BLUE TAPING)
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-44
STEP 13. Check the following connectors.
• TPMS antenna (rear-RH) connector G-28-2
• TPMS receiver connector G-28-1
Check the connectors for loose, corroded or damaged termi-
nals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 14.
NO : Repair it. And then go to Step 17.
STEP 14. Check the following feeder cable.
• The cable between TPMS antenna (rear-RH) connector
G-28-2 (terminal 1) and TPMS receiver connector G-28-1
(terminal 1)
Q: Is there any faults or kinks along the feeder cable
routing?
YES : Repair or replace it. And then go to Step 17.
NO : Go to Step 15.
AC308265
CONNECTOR: G-28-2
AF
G-28-2 (GR)
AC308264
AC307575
CONNECTOR: G-28-1
AF
TPMS RECEIVER
G-28-1 (GR)
(GREEN TAPING)
AC308266
G-28-2 (GR)
CONNECTORS: G-28-1, G-28-2
AH
FEEDER CABLE
CONNECTOR:
COMPONENT SIDE
G-28-1 G-28-2
G-28-1 (GR)
(GREEN TAPING)
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-45
STEP 15. Check the feeder cable core wire for continuity.
(1) Disconnect the following connectors.
• TPMS antenna (rear-RH) connector G-28-2
• TPMS receiver connector G-28-1
(2) Check the feeder cable core wire for continuity as below.
• The cable between TPMS antenna (rear-RH) connector
G-28-2 (terminal 1) and TPMS receiver connector
G-28-1 (terminal 1)
Q: Is there continuity between the feeder cable core wire?
YES : Replace the TPMS antenna (rear-RH) (Refer to
). And then go to Step 16.
NO : Replace the feeder cable. And then go to Step 17.
AC308265
CONNECTOR: G-28-2
AF
G-28-2 (GR)
AC308264
AC307575
CONNECTOR: G-28-1
AF
TPMS RECEIVER
G-28-1 (GR)
(GREEN TAPING)
AC308266
G-28-2 (GR)
CONNECTORS: G-28-1, G-28-2
AH
FEEDER CABLE
CONNECTOR:
COMPONENT SIDE
G-28-1 G-28-2
G-28-1 (GR)
(GREEN TAPING)
TIRE PRESSURE MONITORING SYSTEM (TPMS) DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-46
STEP 16. Execute "Tire Pressure Sensor ID Registration"
on scan tool MB991958 "Special Function."
Q: Is the "Tire Pressure Sensor ID Registration" complete?
YES : Go to Step 18.
NO : Replace the TPMS receiver (Refer to
). And
then go to Step 17.
STEP 17. Execute "Tire Pressure Sensor ID Registration"
on scan tool MB991958 "Special Function."
Q: Is the "Tire Pressure Sensor ID Registration" complete?
YES : Go to Step 18.
NO : Repeat the troubleshooting from Step 1.
STEP 18. Recheck for diagnostic trouble code.
Q: Does diagnostic trouble code 22, 26, 31, 35 or 39 reset?
YES : Repeat the troubleshooting from Step 1.
NO : The procedure is complete.
DTC 23/27/32/36/41: TPMS Transmitter Abnormality (Tire Air Pressure Low)
.
TPMS DTC SET CONDITION
DTC 23, 27, 32, 36 or 41 is set when the TPMS
receiver recognized a low tire pressure from one or
more of the TPMS transmitters. At the same time this
DTC is set, the TPMS warning light illuminates.
TIRE PRESSURE THRESHOLD VALUES
.
TROUBLESHOOTING HINTS (THE MOST LIKELY
CAUSES FOR THIS DTC TO SET ARE:)
• Low tire inflation pressure
• Punctured tire
• Damaged tire valve grommet and/or valve core
• Defective TPMS transmitter
• Malfunction of the TPMS receiver
.
DIAGNOSIS
NOTE: Prior to performing troubleshooting for DTC 23, 27, 32,
36 or 41, first carry out "TPMS Inspection Procedure No.1: The
TPMS Warning Light Stays On" (Refer to
). If the trou-
bleshooting is not complete and DTC 23, 27, 32, 36 or 41 is
set, carry out troubleshooting as described below.
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
ITEM
TIRE PRESSURE kPa
(psi)
Standard pressure at
cold (reference)
200 (29)
Alarm ON pressure
158 (23) or less
Alarm OFF pressure
174 (25) or more
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст