Mitsubishi Montero (2004+). Manual — part 943
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-347
STEP 8. Check intermediate connector D-28, A/C-ECU
connector D-23 <Vehicles with full automatic A/C> and
automatic compressor controller connector D-119
<Vehicles with manual A/C> for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 9.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204188
CONNECTORS : D-23, D-28, D-119
D-23 (B)
D-23, D-119
D-119 (B)
BE
D-28
D-28
20
10
19
9
17
7
16
6
14
4
3
13
5
15
11
1 2
12
8
18
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-348
STEP 9. Check the harness for open circuit between dual
pressure switch connector A-22 terminal 2 and A/C-ECU
connector D-23 terminal 5 <Vehicles with full automatic
A/C> or dual pressure switch connector A-22 terminal 2
and automatic compressor controller connector D-119
terminal 4 <Vehicles with manual A/C>.
Q: Is the harness wire in good condition?
YES : Go to Step 14.
NO : Repair or replace the harness wire.
AC204167
CONNECTOR : A-22
AV
A-22 (BR)
A-22
1 2
AC204188
CONNECTORS : D-23, D-119
D-23 (B)
D-23, D-119
D-119 (B)
BD
20
10
19
9
17
7
16
6
14
4
3
13
5
15
11
1 2
12
8
18
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-349
STEP 10. Measure the switch output voltage at PCM
connector D-134 by backprobing.
(1) Do not disconnect connector D-134.
(2) Start the engine and run at idle.
(3) Operate the A/C.
(4) Measure the voltage between terminal 69 and ground by
backprobing.
• When the A/C is in operation, the voltage should mea-
sure battery positive voltage.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage?
YES : Go to Step 15.
NO : Go to Step 11.
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204918 BI
D-134 HARNESS CONNECTOR :
HARNESS SIDE
76
85
65
72
71
73
82
75
81
74
63 64
66
70
69
68
67
78
87
79
88 89
80
77
86
62
61
83 84
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-350
STEP 11. Check intermediate connector A-03 and PCM
connector D-134 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 12.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204167
CONNECTOR : A-03
AT
A-03 (B)
6
12
5
3 4
2
1
9 10
8
7
11
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст