Mitsubishi Outlander GS45X. Manual — part 217
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-865
.
TECHNICAL DESCRIPTION (COMMENT)
If horns do not sound, the horn input signal circuit or
the ETACS-ECU may be defective.
.
TROUBLESHOOTING HINTS
• Horns may be defective
• Horn relay may be defective
• The ETACS-ECU may be defective
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
DIAGNOSIS
Required Special Tools:
• MB992006: Extra fine probe
• MB991223: Harness set
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
AC901112
Connectors: A-45, A-49
A-49 (B)
AJ
A-45 (B)
ACA02655AW
Connector: C-312
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-866
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
Check if DTC is set to the ETACS-ECU.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect
scan too (M.U.T.-III)
."
(2) Turn the ignition switch to the "ON" position.
(3) Check whether the ETACS-ECU related DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Diagnose the ETACS-ECU. Refer to
.
NO : Go to Step 2.
STEP 2. Check which horn is defective.
Check which horn does not sound when the theft-alarm system
is triggered.
Q: Which horn does not sound?
Horn (HI) and horn (LO) : Go to Step 3.
Horn (HI) only : Go to Step 9.
Horn (LO) only : Go to Step 12.
STEP 3. Check horn relay connector A-15X for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is horn relay connector A-15X in good condition?
YES : Go to Step 4.
NO : Repair the damaged parts.
STEP 4. Check the horn relay.
Refer to
.
Q: Is the horn relay in good condition
YES : Go to Step 5.
NO : Replace the horn relay.
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-867
STEP 5. Measure the voltage at horn relay A-15X.
(1) Remove the relay, and measure at the relay box side.
(2) Measure the voltage between horn relay connector A-15X
(terminal No. 2, 4) and the body ground.
• The voltage should measure approximately 12 volts
(battery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 7.
NO : Go to Step 6.
STEP 6. Check the Wiring harness between horn relay
connector A-15X (terminal No. 2,4) and fusible link (36).
Check the power supply lines for open circuit and short circuit.
Q: Is the check result normal?
YES : The trouble can be an intermittent malfunction (Refer
to GROUP 00, How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Repair the wiring harness between theft-alarm horn
relay connector A-15X and fusible link (36).
STEP 7. Check ETACS-ECU connector C-312 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connector C-312 in good condition?
YES : Go to Step 8.
NO : Repair the damaged parts.
STEP 8. Check the Wiring harness between horn relay
connector A-15X (terminal No. 1) and ETACS-ECU
connector C-312 (terminal No. 11).
Check the output line for open circuit and short circuit.
Q: Is the check result normal?
YES : Go to Step 9.
NO : Repair the wiring harness between horn relay
connector A-15X and ETACS-ECU connector C-312.
STEP 9. Check horn (HI) connector A-49 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is horn (HI) connector A-49 in good condition?
YES : Go to Step 10.
NO : Repair the damaged parts.
AC702831AQ
Relay box side: A-15X
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-868
STEP 10. Check the Wiring harness between horn (HI)
connector A-49 (terminal No. 1) and horn relay connector
A-15X (terminal No. 3).
Check the output line for open circuit and short circuit.
Q: Is the check result normal?
YES : Go to Step 11.
NO : Repair the wiring harness between horn (HI)
connector A-49 and horn relay connector A-15X.
STEP 11. Check the horn (HI) work normally.
Connect the battery as shown, and verify that the horn sounds.
Q: Does horn (HI) work normally?
YES : Go to Step 12.
NO : Replace the horn (HI). Then, go to Step 12.
STEP 12. Check which horn is defective.
Check which horn does not sound when the theft-alarm system
is triggered.
Q: Which horn does not sound?
Horn (HI) and horn (LO) : Go to Step 13.
Horn (HI) only : Replace the ETACS-ECU.
Horn (LO) only : Go to Step 13.
STEP 13. Check horn (LO) connector A-45 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is horn (LO) connector A-45 in good condition?
YES : Go to Step 14.
NO : Repair the damaged parts.
STEP 14. Check the Wiring harness between horn (LO)
connector A-45 (terminal No. 1) and horn relay connector
A-15X (terminal No. 3).
Check the output line for open circuit and short circuit.
Q: Is the check result normal?
YES : Go to Step 15.
NO : Repair the wiring harness between horn (LO)
connector A-45 and horn relay connector A-15X.
AC607630AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст