Mitsubishi Outlander GS45X. Manual — part 101
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-401
STEP 3. Check the ground circuit to the center panel unit.
Measure the resistance at center panel unit connector
C-104.
(1) Disconnect the connector, and measure at the wiring
harness side.
(2) Measure resistance between terminal 9 and ground.
OK: The resistance should be 2 ohm or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 5.
NO : Go to Step 4.
STEP 4. Check the wiring harness between center panel
unit connector C-104 (terminal 9) and ground.
• Check the ground wire for open circuit.
Q: Is the wiring harness between center panel unit
connector C-104 (terminal 9) and ground in good
condition?
YES : Check the trouble symptom.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary.
STEP 5. Check the power supply circuit to the center panel
unit. Measure the voltage at center panel unit connector
C-104.
(1) Disconnect the connector, and measure at the harness side
connector.
(2) Measure voltage between terminal 7 and ground.
OK: The voltage should measure approximately 12
volts (battery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 7.
NO : Go to Step 6.
AC709322 CT
Harness side: C-104
AC709325 BE
Harness side: C-104
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-402
STEP 6. Check the wiring harness between center panel
unit connector C-104 (terminal 7) and fusible link (36).
• Check the power supply line for open circuit and short cir-
cuit.
NOTE: Also ETACS-ECU connector C-307, C-317 for loose,
corroded, or damaged terminals, or terminals pushed back in
the connector. If joint connector ETACS-ECU connector C-307,
C-317 are damaged, repair or replace the connector as
described in GROUP 00E, Harness Connector Inspection
Q: Is the wiring harness between center panel unit
connector C-104 (terminal 7) and fusible link (36) in
good condition?
YES : Check the trouble symptom.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary.
STEP 7. Replace the center panel unit temporarily, and
check the trouble symptom.
Replace the center panel unit temporarily, and check that the
audio works normally.
Q: Is the check result normal?
YES : Replace the center panel unit.
NO : Replace the radio and CD player.
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-403
INSPECTION PROCEDURE 5: Audio illuminations does not work normally.
CAUTION
Before replacing the radio and CD player, ensure that the power supply circuit, the ground circuit and
the communication circuit are normal.
.
OPERATION
• When the position light is illuminated, the audio
illumination is switched to the nighttime illumina-
tion.
• When the brightness is adjusted using the combi-
nation meter rheostat switch, the audio illumina-
tion brightness is also adjusted.
Center Panel Unit Communication Circuit
CENTER PANEL
UNIT
AUDIO SWITCH PANEL
LCD PANEL (AUDIO)
A/C
CONTROL
PANEL
COMBINATION METER
RADIO AND CD PLAYER
ACA02653AC
Connector: C-03
AC709494
AP
Connectors: C-14, C-104, C-119
C-14
C-104
C-119
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-404
.
COMMENTS ON TROUBLE SYMPTOM
The center panel unit, radio and CD player, combina-
tion meter, or communication line from the radio and
CD player to the combination meter may have a
problem.
.
PROBABLE CAUSES
• The combination meter may be defective.
• The radio and CD player may be defective.
• The center panel unit may be defective.
• Damaged harness wires and connectors
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB992006: Extra Fine Probe
STEP 1. Operation check of the center panel unit
Operate the audio control switch of the center panel unit, and
check if the audio operates normally.
Q: Is the check result normal?
YES : Go to Step 2.
NO : Refer to Inspection Procedure 4 "The audio does not
operate normally by operating the radio and CD
player of the center panel unit."
.
STEP 2. Check the combination meter.
Check whether the combination meter works normally.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Diagnose the combination meter (Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст