Mitsubishi Outlander GS45X. Manual — part 1459
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-331
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC U0175 set?
YES : Replace the SRS-ECU (Refer to
).
NO : There is an intermittent malfunction such as poor
engaged connector(s) or open circuit (Refer to
GROUP 00, How to Cope with Intermittent
Malfunction
).
DTC U0176: Side Impact Sensor (Rear) (RH) Communication Error
ZC501967
AC404789
AC701411AB
MB991824
MB991827
MB991910
Data link
connector
CPU
CPU
SIDE IMPACT
SENSOR
(FRONT: RH)
SIDE IMPACT
SENSOR
(REAR: RH)
ACCELERO
METER
ACCELERO
METER
AC803464
Side Impact Sensor (Front, Rear) (RH) Circuit
AC
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-332
CAUTION
If DTC U0176 is set in the SRS-ECU, always diag-
nose the CAN main bus line.
.
CIRCUIT OPERATION
If an impact of set value or more is detected, the side
impact sensor (rear) sends the coded acceleration
data to SRS-ECU via side impact sensor (front).
Based on the acceleration data, SRS-ECU deter-
mines the necessity of curtain air bag deployment,
and then turns ON the power supply circuit to the
inflator.
.
DTC SET CONDITIONS
These DTCs are set if communication between the
side impact sensor (rear) (RH) and the SRS-ECU is
not possible or faulty.
.
TROUBLESHOOTING HINTS
• Damaged wiring harnesses or connectors
• Malfunction of the side impact sensor (rear) (RH)
• Malfunction of the SRS-ECU
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
AC901076
C-27 (Y)
AC
Connector: C-27
AC901079
Connector: D-129
AK
D-129 (Y)
AC901080AF
Connector: D-132
D-132 (Y)
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-333
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 2.
NO : Repair the CAN bus line (Refer to GROUP 54C,
).
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Go to Step 3.
NO : There is an intermittent malfunction such as poor
engaged connector(s) or open circuit (Refer to
GROUP 00, How to Cope with Intermittent
Malfunction
).
ZC501967
AC404789
AC701411AB
MB991824
MB991827
MB991910
Data link
connector
ZC501967
AC404789
AC701411AB
MB991824
MB991827
MB991910
Data link
connector
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-334
STEP 3. Check for any diagnostic trouble code. (Using
scan tool MB991958, read the diagnostic trouble code.)
Check the side impact sensor (rear) (RH).
(1) Disconnect the negative battery terminal.
(2) Alternate the side impact sensor (rear) (RH) and side
impact sensor (rear) (LH), and then install the alternated
sensors.
(3) Connect the negative battery terminal.
(4) Erase diagnostic trouble code from memory, and check the
diagnostic trouble code.
Q: Is DTC U0173 set?
YES : Replace the side impact sensor (rear) (RH) with a
new one. (Refer to
). Go to Step 5.
NO : Go to Step 4.
STEP 4. Check the harness wires for open circuit and short
circuit between side impact sensor (rear) (RH) connector
D-132 (terminal No.1 and 2) and side impact sensor (front)
(RH) connector D-129 (terminal No.4 and 3).
Q: Are the harness wires between side impact sensor
(rear) (RH) connector D-132 (terminal No.1 and 2) and
side impact sensor (front) (RH) connector D-129
(terminal No.4 and 3) in good condition?
YES : Go to Step 5.
NO : Repair the harness wires between side impact sensor
(rear) (RH) connector D-132 and side impact sensor
(front) (RH) connector D-129.
ZC501967
AC404789
AC701411AB
MB991824
MB991827
MB991910
Data link
connector
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст