Mitsubishi Outlander GS45X. Manual — part 8
COMBINATION METER
TSB Revision
CHASSIS ELECTRICAL
54A-29
SERVICE SPECIFICATIONS
M1540200200300
Item
Standard Value
Speedometer indication tolerance mph (km/h)
<Except vehicles for CANADA>
10 (16)
8.5
− 11.5 (13.6 − 18.4)
25 (40)
23.5
− 26.5 (37.6 − 42.4)
50 (80)
48.5
− 51.5 (77.6 − 82.4)
75 (120)
73.5
− 76.5 (117.6 − 122.4)
100 (161)
98.5
− 102.5 (158.6 − 165.0)
125 (201)
123.5
− 127.5 (198.6 − 205.0)
Speedometer indication tolerance km/h (mph)
<Vehicles for CANADA>
20 (12.4)
19
− 24 (11.8 − 14.9)
40 (24.8)
40
− 44 (24.8 − 27.3)
80 (49.7)
80
− 85 (49.7 − 52.8)
120 (74.6)
120.5
− 125.5 (74.9 − 78.0)
160 (99.4)
160.5
− 165.5 (99.7 − 102.8)
200 (124.3)
200.5
− 207.0 (124.6 − 128.6)
Tachometer indication tolerance r/min
The value in parentheses is a reference value.)
600
550
− 650
(2,000)
(1,950
− 2,050)
3,000
2,950
− 3,050
(4,000)
(3,950
− 4,050)
5,000
4,950
− 5,050
6,000
5,950
− 6,050
(7,000)
(6,950
− 7,050)
(8,000)
(7,950
− 8,050)
FWD
Fuel level sensor resistance (
Ω)
Stopper position "F"
13.0
± 1.0
Stopper position "E"
120.0
± 1.0
Fuel level sensor float height mm (in)
Stopper position "F"
(height A)
201.6 (7.9)
Stopper position "E"
(height B)
18.0 (0.7)
AWD
Fuel level sensor
resistance (
Ω)
Fuel level sensor
(main)
Stopper position "F"
6.5
± 1.0
Stopper position "E"
44.7
± 1.0
Fuel level sensor
(sub)
Stopper position "F"
6.5
± 1.0
Stopper position "E"
75.3
± 1.0
Fuel level sensor
float height mm
(in)
Fuel level sensor
(main)
Stopper position "F"
(height A)
166.2 (6.5)
Stopper position "E"
(height B)
38.8 (1.5)
Fuel level sensor
(sub)
Stopper position "F"
(height A)
48.8
± 3.0 (1.9 ± 0.1)
Stopper position "E"
(height B)
238.0
± 3.0 (9.3 ± 0.1)
COMBINATION METER
TSB Revision
CHASSIS ELECTRICAL
54A-30
SPECIAL TOOLS
M1540200300200
Tool
Tool number and
name
Supersession
Application
MB991958
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991914
f. MB991825
g. MB991826
M.U.T.-III sub
assembly
a. Vehicle
communication
interface (V.C.I.)
b. M.U.T.-III USB
cable
c. M.U.T.-III main
harness A
(Vehicles with
CAN
communication
system)
d. M.U.T.-III main
harness B
(Vehicles without
CAN
communication
system)
e. M.U.T.-III main
harness C (for
Chrysler models
only)
f. M.U.T.-III
measurement
adapter
g. M.U.T.-III trigger
harness
MB991824-KIT
NOTE: G: MB991826
M.U.T.-III Trigger
Harness is not
necessary when
pushing V.C.I. ENTER
key.
CAUTION
M.U.T.-III main harness A
(MB991910) should be used.
M.U.T.-III main harness B and C
should not be used for this
vehicle.
Combination meter check
(Diagnostic trouble code, service
data)
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
Do not use
a
b
c
d
e
f
g
Do not use
COMBINATION METER
TSB Revision
CHASSIS ELECTRICAL
54A-31
COMBINATION METERS DIAGNOSTIC
STANDARD FLOW OF DIAGNOSTIC
TROUBLESHOOTING
M1540203800215
Refer to GROUP 00, Contents of troubleshooting
DIAGNOSTIC FUNCTION
M1540200500130
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
MB991223
a. MB991219
b. MB991220
c. MB991221
d. MB991222
Harness set
a. Test harness
b. LED harness
c. LED harness
adaptor
d. Probe
General service tools Continuity check and voltage
measurement at harness wire or
connector for loose, corroded or
damaged terminals, or terminals
pushed back in the connector.
a. Connector pin contact
pressure inspection
b. Power circuit inspection
c. Power circuit inspection
d. Commercial tester connection
MB992006
Extra fine probe
−
Making voltage and resistance
measurement during
troubleshooting
MB990784
Ornament remover
General service tool
Removal of switch, trim, etc.
Tool
Tool number and
name
Supersession
Application
MB991223
a
d
c
b
Do not use
BD
MB992006
MB990784
COMBINATION METER
TSB Revision
CHASSIS ELECTRICAL
54A-32
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
1. Ensure that the ignition switch is at the "LOCK" (OFF)
position.
2. Start up the personal computer.
3. Connect special tool MB991827 to special tool MB991824
and the personal computer.
4. Connect special tool MB991910 to special tool MB991824.
5. Connect special tool MB991910 to the data link connector.
6. Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE: When special tool MB991824 is energized, special
tool MB991824 indicator light will be illuminated in a green
color.
7. Start the M.U.T.-III system on the personal computer.
NOTE: Disconnecting scan tool MB991958 is the reverse of the
connecting sequence, making sure that the ignition switch is at
the "LOCK" (OFF) position.
HOW TO READ AND ERASE DIAGNOSTIC
TROUBLE CODES
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
NOTE: If the battery voltage is low, diagnostic trouble codes will
not be set. Check the battery if scan tool MB991958 does not
display.
1. Connect scan tool MB991958 to the data link connector.
2. Turn the ignition switch to the "ON" position.
3. Select "System select" from the start-up screen.
4. Select "From 2006 MY" of "Model Year." When the "Vehicle
Information" is displayed, check the contents.
5. Select "Meter" from "System List," and press the "OK"
button.
NOTE: When the "Loading Option Setup" list is displayed,
check the applicable item.
6. Select "Diagnostic Trouble Code" to read the DTC.
7. If a DTC is set, it is shown.
8. Choose "Erase DTCs" to erase the DTC.
HOW TO DIAGNOSE THE CAN BUS LINES
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст