Mitsubishi Outlander GS45X. Manual — part 1587
RADIATOR
TSB Revision
ENGINE COOLING
14-51
INSTALLATION SERVICE POINT
.
>>A<< RADIATOR HOSE/HOSE CLIP INSTALLA-
TION
CAUTION
Never reuse the hose clip whose claw is broken off to pre-
vent the rusting.
1. Make mating mark on a new hose clip in the same position
as the remove one.
2. Insert the radiator hose until the protrusion of the pipe.
3. Align the mating marks on the radiator hose and hose clip.
4. Remove the hose clip claw and shorten the hose clip, then
install the radiator hose.
AC606082
Protrusion
Pipe, fitting, or etc.
AU
Mating marks
RADIATOR
TSB Revision
ENGINE COOLING
14-52
REMOVAL AND INSTALLATION <3.0L ENGINE>
M1141001502903
Pre-removal operation
• Engine coolant Draining (Refer to
• Air Cleaner Assembly Removal (Refer to GROUP 15, Air
Cleaner
).
Post-installation operation
• Air Cleaner Assembly Installation (Refer to GROUP 15,
Air Cleaner
).
• Engine Coolant Refilling and Check (Refer to
AC808978
4
3
5
7
8
10
19
19
20
11
23
21
22
29
24
16
15
AB
17
N
6
9
N
12
N
13
12
N
14
18
25
26
27
28
20
12 ± 2 N·m
106 ± 17 in-lb
12 ± 2 N·m
106 ± 17 in-lb
10 ± 2 N·m
89 ± 17 in-lb
22 ± 3 N·m
16 ± 2 ft-lb
12 ± 2 N·m
106 ± 17 in-lb
5.0 ± 1.0 N·m
44 ± 8 in-lb
3.4 ± 0.5 N·m
30 ± 4 in-lb
1
2
N
3.4 ± 0.5 N·m
30 ± 4 in-lb
Radiator removal steps
•
Engine room under cover front
(Refer to GROUP 51
− Under
Cover
).
1.
Radiator drain plug
2.
O-ring
3.
Radiator cap
4.
A/T fluid cooler feed hose assembly
5.
Radiator condenser tank hose
<<
A
>> >>
A
<< 6.
Hose clip
<<
A
>> >>
A
<< 7.
Radiator upper hose
8.
Radiator cap assembly
<<
A
>> >>
A
<< 9.
Hose clip
<<
A
>> >>
A
<< 10. Radiator upper hose
11. Radiator hose clamp
<<
A
>> >>
A
<< 12. Hose clip
<<
A
>> >>
A
<< 13. Radiator lower hose
14. Radiator hose support
15. Radiator fan motor connector
16. Condenser fan motor connector
17. Fan, fan motor and fan shroud
assembly
•
Headlight support upper panel
(Refer to GROUP 42A
− Loose
).
18. Radiator assembly
19. Support upper insulator
20. Support lower insulator
Radiator removal steps
RADIATOR
TSB Revision
ENGINE COOLING
14-53
REMOVAL SERVICE POINT
.
<<A>> HOSE CLIP/RADIATOR HOSE REMOVAL
1. Make mating marks on the radiator hose and the hose clip
as shown to install them in the original position.
2. Break off the tip of hose clip claw and spread out the hose
clip, then disconnect the radiator hose.
NOTE: If there is a hose clip claw, the hose clip cannot
spread to capacity because the claw contacts the hose clip.
INSTALLATION SERVICE POINT
.
>>A<< RADIATOR HOSE/HOSE CLIP INSTALLA-
TION
CAUTION
Never reuse the hose clip whose claw is broken off to pre-
vent the rusting.
1. Make mating mark on a new hose clip in the same position
as the remove one.
21. Radiator condenser tank
22. Radiator condenser tank bracket
Fan shroud removal steps
5.
Radiator condenser tank hose
<<
A
>> >>
A
<< 6.
Hose clip
<<
A
>> >>
A
<< 7.
Radiator upper hose
8.
Radiator cap assembly
15. Radiator fan motor connector
16. Condenser fan motor connector
17. Fan, fan motor and fan shroud
assembly
23. Radiator fan
24. Radiator fan motor harness
25. Radiator fan motor
26. Condenser fan
27. Condenser fan motor harness
28. Condenser fan motor
29. Fan shroud
Radiator removal steps
AC606081
Mating marks
AE
AC302615
Hose clip
Claw (Tip)
AE
RADIATOR
TSB Revision
ENGINE COOLING
14-54
2. Insert the radiator hose until the protrusion of the pipe.
3. Align the mating marks on the radiator hose and hose clip.
4. Remove the hose clip claw and shorten the hose clip, then
install the radiator hose.
AC606082
Protrusion
Pipe, fitting, or etc.
AU
Mating marks
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст