Mitsubishi Outlander GS45X. Manual — part 1599
CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-45
Inspection Procedure 3: When the "CANCEL" Switch is Set to ON, Cruise Control System is not
Cancelled.
.
COMMENT
The cause is probably an open-circuit in the output
circuit inside the "CANCEL" switch.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CASE:)
• Malfunction of the cruise control switch.
• Malfunction of the ECM.
DIAGNOSTIC PROCEDURE
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
STEP 1. Using scan tool MB991958, check the data list
item 75: Cancel switch.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector
(Refer to
).
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to data reading mode for cruise
control system (Refer to
).
• Item 75: Cancel switch.
• When the "CANCEL" switch is pressed, the display
on scan tool MB991958 should be "ON".
• When the "CANCEL" switch is released, the display
on scan tool MB991958 should be "OFF".
Q: Is the switch operating properly?
YES : Go to Step 2.
NO : Repair the cruise control switch system (Refer to
, Diagnosis Code Procedures
− DTC 15:
Cruise Control Switch System.) Then go to Step 3 .
STEP 2. Check the symptom.
Q: When the "CANCEL" switch is pressed, is the cruise
control cancelled?
YES : It can be assumed that this malfunction is intermittent
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
).
NO : Replace the ECM [Refer to GROUP 13A, Engine
Control Module (ECM)
] <2.4L Engine> or
[Refer to GROUP 13B, Engine Control Module (ECM)
] <3.0L Engine>. Then go to Step 3.
ZC501967
AC404789
AC703911AB
MB991824
MB991827
MB991910
Data link
connector
CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-46
STEP 3. Check the symptom.
Q: When the "CANCEL" switch is pressed, is the cruise
control cancelled?
YES : The procedure is complete.
NO : Return to Step 1.
Inspection Procedure 4: Cruise Control cannot be Set (No Response "COAST/SET" Switch and
"ACC/RES" Switch is Pressed).
.
COMMENT
The fail-safe function is probably canceling cruise
control system. In this case, checking the cruise con-
trol system, MFI system, CVT system <2.4L Engine>
or A/T system <3.0L Engine>, ASC system <vehicles
with ASC> and CAN bus line system for DTCs. The
scan tool MB991958 can also be used to check if the
circuits of each input switch are normal or not by
checking the data list.
NOTE: Press the cruise control switches one by one
securely. Otherwise, the cruise control system may
not be started.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CASE:)
• Malfunction of the CAN bus line system.
• Malfunction of the MFI system.
• Malfunction of the CVT system <2.4L Engine>.
• Malfunction of the A/T system<3.0L Engine>.
• Malfunction of the ASC system <vehicles with
ASC>.
• Malfunction of the cruise control switch.
• Malfunction of the stoplight switch.
• Malfunction of the transmission range switch.
• Malfunction of the TCM.
• Malfunction of the ECM.
DIAGNOSTIC PROCEDURE
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
CAUTION
If there is any problem in the CAN bus lines, an incorrect
DTC may be set. Prior to this diagnosis, diagnose the CAN
bus lines (Refer to GROUP 54C, Trouble code diagnosis
.)
CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-47
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector
(Refer to
).
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to diagnose the CAN bus line
(Refer to
).
Q: Is the check result satisfactory?
YES : Go to Step 2.
NO : Repair the CAN bus lines (Refer to GROUP 54C,
Diagnosis
− CAN Bus Diagnostics Chart
Then go to Step 12.
STEP 2. Using scan tool MB991958, check for ECM option
coding data.
(1) Connect scan tool MB991958 to the data link connector
(Refer to
.)
(2) Turn the ignition switch to the "ON" position.
(3) Check for ECM option coding data (Refer to GROUP 00,
Precautions Before Service
− Coding List
Q: Is the cruise control item of the ECM option coding data
enabled?
YES : Go to Step 3.
NO : Set the ECM option coding data again. (Refer to
GROUP 00, Precautions Before Service
− Coding List
.) Then go to Step 12.
ZC501967
AC404789
AC703911AB
MB991824
MB991827
MB991910
Data link
connector
CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-48
STEP 3. Using scan tool MB991958, read the MFI system
DTC.
(1) Connect scan tool MB991958 to the data link connector
(Refer to
).
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to check for MFI system DTC
(Refer to GROUP 13A, MFI Diagnosis
− Diagnostic
Function
) <2.4L Engine> or (Refer to GROUP
13B, MFI Diagnosis
− Diagnostic Function
) <3.0L
Engine>.
Q: Is any DTC set?
YES : Repair the MFI system (Refer to GROUP 13A, MFI
Diagnosis
− Diagnostic Trouble Code Chart
) <2.4L Engine> or (Refer to GROUP 13B,
MFI Diagnosis
− Diagnostic Trouble Code Chart
) <3.0L Engine>. Then go to Step 12.
NO : Go to Step 4 <2.4L Engine>.
NO : Go to Step 5 <3.0L Engine>.
STEP 4. Using scan tool MB991958, read the CVT system
DTC <2.4L Engine>.
(1) Connect scan tool MB991958 to the data link connector
(Refer to
).
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to check for CVT system DTC
(Refer to GROUP 23A, Diagnosis
− Diagnostic Function
Q: Is any DTC set?
YES : Repair the CVT system (Refer to GROUP 23A,
Diagnosis
− Diagnostic Trouble Code Chart
). Then go to Step 12.
NO : Go to Step 6.
STEP 5. Using scan tool MB991958, read the A/T system
DTC <3.0L Engine>.
(1) Connect scan tool MB991958 to the data link connector
(Refer to
).
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to check for A/T system DTC
(Refer to GROUP 23C, Automatic Transaxle Diagnosis
−
Diagnostic Function
Q: Is any DTC set?
YES : Repair the A/T system (Refer to GROUP 23C,
Automatic Transaxle Diagnosis
− Diagnostic Trouble
). Then go to Step 12.
NO : Go to Step 6 <vehicles with ASC>.
NO : Go to Step 7 <vehicles without ASC>.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст