Mitsubishi Outlander GS45X. Manual — part 1261
TROUBLESHOOTING
TSB Revision
LOCAL INTERCONNECT NETWORK (LIN)
54B-37
Recheck for diagnostic trouble code.
Check again if the DTC is set to the ETACS-ECU.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Ensure that the ignition switch is at the "LOCK" (OFF)
position.
(2) Start up the personal computer.
(3) Connect special tool MB991827 to special tool MB991824
and the personal computer.
(4) Connect special tool MB991910 to special tool MB991824.
(5) Connect special tool MB991910 to the data link connector.
(6) Erase the DTC.
(7) Turn the ignition switch to the "ON" position.
(8) Check if the DTC is set.
(9) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the sunroof motor assembly.
NO : A poor connection, open circuit, or other intermittent
malfunctions in the LIN bus lines between the sunroof
motor assembly and the ETACS-ECU (Refer to
GROUP 00, How to Cope with Intermittent
Malfunction
).
DTC U1512: Lighting control sensor checksum error <Vehicles with auto light function>
.
TROUBLE JUDGMENT
The ETACS-ECU will set DTC U1512 when abnor-
mal signals are received from the lighting control
sensor.
.
TROUBLESHOOTING HINTS
• The lighting control sensor may be defective.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
TROUBLESHOOTING
TSB Revision
LOCAL INTERCONNECT NETWORK (LIN)
54B-38
Recheck for diagnostic trouble code.
Check again if the DTC is set to the ETACS-ECU.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
(2) Erase the DTC.
(3) Turn the ignition switch to the "ON" position.
(4) Check if the DTC is set.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the lighting control sensor.
NO : A poor connection, open circuit, or other intermittent
malfunctions in the LIN bus lines between the lighting
control sensor and the ETACS-ECU (Refer to
GROUP 00, How to Cope with Intermittent
Malfunction
).
DTC U1514: Bit error (LIN)
.
TROUBLE JUDGMENT
The ETACS-ECU receives and sends data simulta-
neously. If the data contains a fault, the ETACS-ECU
will set DTC U1514.
.
TROUBLESHOOTING HINTS
• The slave ECU may be defective.
• The ETACS-ECU may be defective.
• Electrical noise generated in the LIN bus lines
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
TROUBLESHOOTING
TSB Revision
LOCAL INTERCONNECT NETWORK (LIN)
54B-39
Recheck for diagnostic trouble code.
Check again if the DTC is set to the ETACS-ECU.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Ensure that the ignition switch is at the "LOCK" (OFF)
position.
(2) Start up the personal computer.
(3) Connect special tool MB991827 to special tool MB991824
and the personal computer.
(4) Connect special tool MB991910 to special tool MB991824.
(5) Connect special tool MB991910 to the data link connector.
(6) Erase the DTC.
(7) Turn the ignition switch to the "ON" position.
(8) Check if the DTC is set.
(9) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES <A DTC other than U1514 is set.> : Replace the
appropriate ECU.
YES <The DTC U1514 is set.> : Replace the ETACS-ECU.
NO <The DTC is not set.> : The trouble can be an
intermittent malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
TROUBLESHOOTING
TSB Revision
LOCAL INTERCONNECT NETWORK (LIN)
54B-40
DTC U1515: No-Bus activity error (LIN)
LIN Communication Circuit
INTERFACE CIRCUIT
INPUT
CIRCUIT
CPU
COLUMN-ECU
COLUMN
SWITCH
POWER WINDOW
MAIN SWITCH
SUNROOF
MOTOR
ASSEMBLY
LIN DRIVE CIRCUIT
ETACS-ECU
LIGHTING
CONTROL
SENSOR
LIN
CUTOFF
CONTROL
UNIT
THEFT-
ALARM
SIREN
THEFT-
ALARM
SENSOR
AC901112
Connectors: A-03, A-62
A-03 (B)
AX
A-62 (B)
AC702922 AE
Connector: C-212
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст