Mitsubishi Outlander GS45X. Manual — part 628
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-335
DTC P0222: Throttle Position Sensor (sub) Circuit Low Input
.
CIRCUIT OPERATION
• A 5-volt power supply is applied on the throttle
position sensor (sub) power terminal (terminal
No. 5) from the ECM (terminal No. 12).
• A voltage that is according to the throttle opening
angle is sent to the ECM (terminal No. 11) from
the throttle position sensor (sub) output terminal
(terminal No. 6).
AK604243
1
2
3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
6
1 2 3 4 5
5 V
12
5
11
13
6
3
THROTTLE POSITION SENSOR (SUB) CIRCUIT
THROTTLE POSITION
SENSOR (SUB)
B-10
HALL IC
AC
B-08
(MU805200)
ENGINE
CONTROL
MODULE
YELLO
W
-RED
YELLO
W
-PINK
YELLO
W
-GRA
Y
AK704102AB
Intake manifold
Connector: B-08
B-08 (B)
AK704090AB
Connector: B-10
B-10 (GR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-336
• The ground terminal (terminal No. 3) is grounded
with ECM (terminal No. 13).
.
TECHNICAL DESCRIPTION
• The throttle position sensor (sub) outputs voltage
which corresponds to the throttle valve opening
angle.
• The ECM checks whether the voltage is within a
specified range.
.
DESCRIPTIONS OF MONITOR METHODS
Throttle position sensor (sub) output voltage is out of
specified range.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS
(Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
DTC SET CONDITIONS
Logic Flow Chart
Check Condition
• Ignition switch is "ON" position.
Judgement Criterion
• Throttle position sensor (sub) output voltage
should be 0.2 volt or less for 0.3 second.
.
No
No
No
Malfunction
End
Good
Output voltage <= 0.2V
Output voltage >= 4.8V
AK604318
Start
Yes
Yes
Yes
Continuous
failure for 0.3sec
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-337
OBD-II DRIVE CYCLE PATTERN
None.
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• Throttle position sensor failed.
• Open or shorted throttle position sensor (sub) cir-
cuit, harness damage, or connector damage.
• ECM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
• MB991658: Test Harness
STEP 1. Using scan tool MB991958, check data list item 15:
Throttle Position Sensor (sub).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Detach the intake air hose at the throttle body.
(4) Disconnect the connector of the throttle position sensor.
(5) Use test harness special tool (MB991658) to connect only
terminals No. 3, No. 4, No. 5, and No. 6.
(6) Set scan tool MB991958 to the data reading mode for item
15, Throttle Position Sensor (sub).
• Output voltage should be 4.0 volts or more when the
throttle valve is fully closed with your finger.
• Output voltage should be 1.0 volt or less when the throt-
tle valve is fully open with your finger.
(7) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Go to Step 2.
STEP 2. Check harness connector B-08 at throttle position
sensor for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 11.
AK700568AB
MB991824
MB991827
MB991910
Data link
connector
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-338
STEP 3. Measure the sensor supply voltage at throttle
position sensor harness side connector B-08.
(1) Disconnect the connector B-08 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 5 and ground.
• Voltage should be between 4.9 and 5.1 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.9 and 5.1 volts?
YES : Go to Step 7.
NO : Go to Step 4.
STEP 4. Check harness connector B-10 at ECM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 11.
STEP 5. Check for open circuit and short circuit to ground
between throttle position sensor connector B-08 (terminal
No. 5) and ECM connector B-10 (terminal No. 12).
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair it. Then go to Step 11.
1
6 5 4 3 2
AK203049
B-08 harness
connector:
component side
AF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст