Mitsubishi Outlander GS45X. Manual — part 1076
DOOR
TSB Revision
BODY
42A-107
STEP 8. Check ETACS-ECU connector C-315 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connector C-315 in good condition?
YES : Go to Step 9.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. When the front power window sub switch
(RH) is operated, the front power window (RH) should
raise and lower normally.
STEP 9. Check the wiring harness between ETACS-ECU
connector C-315 (terminal 8) and front power window sub
switch connector E-06 (terminal 6).
• Check the power supply line for open circuit and short cir-
cuit.
NOTE: Also check intermediate connector C-112. If intermedi-
ate connectors C-112 is damaged, repair or replace the dam-
aged component(s) as described in GROUP 00E, Harness
Connector Inspection
.
Q: Is the wiring harness between ETACS-ECU connector
C-315 (terminal 8) and front power window sub switch
connector E-06 (terminal 6 in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. When the
front power window sub switch is operated, the front
power window (RH) should raise and lower normally.
STEP 10. Check the ground circuit to the front power
window sub switch. Measure the resistance at front power
window sub switch connector E-06.
(1) Disconnect front power window sub switch connector E-06
and measure the resistance available at the wiring harness
side of the connector.
(2) Measure the resistance value between terminal 5 and
ground, and also between terminal 8 and ground.
• The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 12.
NO : Go to Step 11.
AC702473
Connector E-06
AI
(harness side)
DOOR
TSB Revision
BODY
42A-108
STEP 11. Check the wiring harness between power window
main switch connector E-19 (terminals 1, 3) and front
power window sub switch connector E-06 (terminals 8, 5).
• Check the power supply lines for open circuit and short cir-
cuit.
NOTE: Also check intermediate connectors C-112 and C-126.
If intermediate connector C-112 or C-126 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between power window main
switch connector E-19 (terminals 1, 3) and front power
window sub switch connector E-06 (terminals 8, 5) in
good condition?
YES : Replace the power window main switch. When the
front power window sub switch (RH) is operated, the
front power window (RH) should raise and lower
normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. When the
front power window sub switch (RH) is operated, the
front power window (RH) should raise and lower
normally.
STEP 12. Check the wiring harness between front power
window sub switch connector E-06 (terminals 4, 7) and
front power window motor (RH) connector E-03 (terminals
1, 4).
• Check the power supply lines for open circuit and short cir-
cuit.
Q: Is the wiring harness between front power window sub
switch connector E-06 (terminals 4, 7) and front power
window motor (RH) connector E-03 (terminals 1, 4) in
good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. When the
front power window sub switch (RH) is operated, the
front power window (RH) should raise and lower
normally.
DOOR
TSB Revision
BODY
42A-109
STEP 13. Check rear power window sub switch (LH)
connector E-25 and rear power window motor (LH)
connector E-26 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
Q: Are rear power window sub switch (LH) connector E-25
and rear power window motor (LH) connector E-26 in
good condition?
YES : Go to Step 14.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. When the rear power window sub switch
(LH) is operated, the rear power window (LH) should
raise and lower normally.
STEP 14. Check the rear power window sub switch (LH) for
continuity.
(1) Remove the rear power window sub switch (LH). Refer to
GROUP 42A, Door, Door Glass and Regulator
.
(2) Check continuity when the rear power window sub switch
(LH) is operated to "UP" or "DOWN" position.
Q: Is the rear power window sub switch (LH) normal?
YES : Go to Step 15.
NO : Replace the rear power window sub switch (LH).
When the rear power window sub switch (LH) is
operated, the rear power window (LH) should raise
and lower normally.
Switch
position
Tester
connection
Specified
condition
UP
4
− 5, 6 − 7
Continuity
exists (2
Ω or
less)
OFF
4
− 5, 7 − 8
DOWN
4
− 6, 7 − 8
AC703138AB
8
3
4 5
1
2
6 7
<Rear door>
DOOR
TSB Revision
BODY
42A-110
STEP 15. Check the rear power window motor (LH).
(1) Remove the rear power window regulator assembly (LH).
Refer to GROUP 42A, Door, Door Glass and Regulator
(2) Connect a battery to the motor terminal, and check that the
motor runs freely.
Q: Is the rear power window motor (LH) normal?
YES : Go to Step 16.
NO : Replace the rear power window motor (LH). When the
rear power window sub switch (LH) is operated, the
rear power window (LH) should raise and lower
normally.
STEP 16. Check the battery power supply circuit to the rear
power window sub switch (LH). Measure the voltage at rear
power window sub switch (LH) connector E-25.
(1) Disconnect rear power window sub switch (LH) connector
E-25 and measure the voltage available at the wiring
harness side of the connector.
(2) Measure the voltage between terminal 6 and ground.
• The voltage should measure approximately 12 volts
(battery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 19.
NO : Go to Step 17.
Battery connection
Slider position
• Connect terminal 1 to
the negative battery
terminal
• Connect terminal 4 to
the positive battery
terminal
UP
• Connect terminal 4 to
the negative battery
terminal
• Connect terminal 1 to
the positive battery
terminal
DOWN
AC703136AB
AC702474
Connector E-25
AI
(harness side)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст