Mitsubishi Outlander GS45X. Manual — part 689
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-579
STEP 3. Measure the power supply voltage at throttle
actuator control motor relay harness side connector A-21X
(1) Disconnect the connector A-21X and measure at the
harness side.
(2) Measure the voltage between terminal No. 4 and ground.
• Voltage should be battery positive voltage.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 4.
NO : Repair it harness wire between battery and throttle
actuator control motor relay connector A-21X
(terminal No. 4) because of open circuit or short
circuit to ground. Then go to Step 14.
STEP 4. Measure the power supply voltage at throttle
actuator control motor relay harness side connector
A-21X.
(1) Disconnect the connector A-21X and measure at the
harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 2 and ground.
• Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 6.
NO : Go to Step 5.
STEP 5. Check harness connector A-33X at MFI relay for
damage.
Q: Is the harness connector in good condition?
YES : Repair harness wire between MFI relay connector
A-33X (terminal No. 2) and throttle actuator control
motor relay connector A-21X (terminal No. 2)
because of open circuit or short circuit to ground.
Then go to Step 14.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 14.
2
1
3
4
AK604215 AC
A-21X harness
connector:
component side
AK604216
2
1
3
4
AC
A-21X harness
connector:
component side
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-580
STEP 6. Measure the power supply voltage at ECM harness
side connector B-11.
(1) Disconnect the connector B-11 and measure at the harness
side.
(2) Short-circuit the terminal No. 73 of the ECM harness
connector to the ground.
(3) Measure the voltage between terminal No. 84 and ground.
• Voltage should be battery positive voltage.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 7.
NO : Repair harness wire between throttle actuator control
motor relay connector A-21X (terminal No. 1) and
ECM connector B-11 (terminal No. 84) because of
open circuit or short circuit to ground. Then go to Step
14.
82 81 80 79 78 77 76 75 74 73 72 71
94 93 92 91 90 89 88 87 86 85 84 83
99 98 97 96 95
100
101
102
103
104
105
106
112
113
114
109 108
107
110
111
115
116
117
118
AK604217 AC
B-11 harness
connector:
component side
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-581
STEP 7. Measure the power supply voltage at ECM harness
side connector B-11.
(1) Disconnect the connector B-11 and measure at the harness
side.
(2) Short-circuit the terminals No. 73 and No. 84 of the ECM
harness connector to the ground.
(3) Measure the voltage between terminal No. 72 and ground.
• Voltage should be battery positive voltage.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 10.
NO : Go to Step 8.
STEP 8. Check for open circuit and short circuit to ground
between throttle actuator control motor relay connector
A-21X (terminal No. 3) and ECM connector B-11 (terminal
No. 72).
Q: Is the harness wire in good condition?
YES : Go to Step 9.
NO : Repair it. Then go to Step 14.
STEP 9. Check for harness damage between MFI relay
connector A-33X (terminal No. 2) and throttle actuator
control motor relay connector A-21X (terminal No. 2).
Q: Is the harness wire in good condition?
YES : Repair harness wire between throttle actuator control
motor relay connector A-21X (terminal No. 1) and
ECM connector B-11 (terminal No. 84) because of
harness damage. Then go to Step 14.
NO : Repair it. Then go to Step 14.
82 81 80 79 78 77 76 75 74 73 72 71
94 93 92 91 90 89 88 87 86 85 84 83
99 98 97 96 95
100
101
102
103
104
105
106
112
113
114
109 108
107
110
111
115
116
117
118
AK604218 AC
B-11 harness
connector:
component side
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-582
STEP 10. Check harness connector B-11 at ECM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 14.
STEP 11. Check for harness damage between battery and
throttle actuator control motor relay connector A-21X
(terminal No. 4).
Q: Is the harness wire in good condition?
YES : Go to Step 12.
NO : Repair it. Then go to Step 14.
STEP 12. Check for harness damage between throttle
actuator control motor relay connector A-21X (terminal No.
3) and ECM connector B-11 (terminal No. 72).
Q: Is the harness wire in good condition?
YES : Go to Step 13.
NO : Repair it. Then go to Step 14.
STEP 13. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P0657 set?
YES : Replace the ECM. When the ECM is replaced,
register the ID code. Refer to GROUP 42B, Diagnosis
− ID Code Registration Judgment Table <Vehicles
or GROUP 42C, Diagnosis
− ID
Codes Registration Judgment Table <Vehicles with
WCM>
. Then go to Step 14.
NO : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
AK700568AB
MB991824
MB991827
MB991910
Data link
connector
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст