Mitsubishi Outlander GS45X. Manual — part 392
WHEEL SPEED SENSOR
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-189
REMOVAL SERVICE POINT
.
<<A>> HYDRAULIC UNIT (ABS-ECU) REMOVAL
CAUTION
• Be careful when removing the hydraulic unit because it
is heavy.
• Never loosen the nuts and the bolts because the
hydraulic unit cannot be disassembled.
• Do not drop or shock the hydraulic unit.
• Do not turn the hydraulic unit upside down or lay down
the unit because the inner air becomes difficult to be
bled.
INSTALLATION SERVICE POINT
.
>>A<< BRAKE TUBE CONNECTION
Install the brake pipe to the hydraulic unit as shown in the fig-
ure.
1. To rear brake (RH) <Marking color: White>
2. From master cylinder (secondary) <Marking color: Yellow>
3. To front brake (LH) <Marking color: Red and white>
4. To front brake (RH) <Marking color: Orange and white>
5. From master cylinder (primary) <Marking color: Blue>
6. To rear brake (LH) <Marking color: Pink>
WHEEL SPEED SENSOR
REMOVAL AND INSTALLATION
M1352008301574
CAUTION
The vehicle speed detection encoder collects any
metallic particle easily, because it is magnetized.
Make sure that the encoder should not collect
any metallic particle. Check that there is not any
trouble prior to reassembling it.
ZC601084
AC703834AB
1
6
5
3
4
2
Pre-removal and post-installation operation
• Air cleaner body assembly removal and installation <Refer to GROUP 15 − Air Cleaner
(3000)>.
Front wheel speed sensor (LH)
• Quarter trim removal and installation (Refer to GROUP 52A − Trim
). Rear wheel speed sensor
WHEEL SPEED SENSOR
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-190
ACA01999
<Rear (vehicles with 5 seating capacity)>
3
<Front>
2
1
1
2
3
4
5
13 ± 2 N·m
111 ± 22 in-lb
5
11 ± 2 N·m
98 ± 17 in-lb
8.5 ± 1.5 N·m
76 ± 13 in-lb
11 ± 2 N·m
98 ± 17 in-lb
13 ± 2 N·m
111 ± 22 in-lb
8.5 ± 1.5 N·m
76 ± 13 in-lb
AB
4
11 ± 2 N·m
6
8
9
10
8
9
10
6
11
11
7
7
N
N
8.5 ± 1.5 N·m
76 ± 13 in-lb
8.5 ± 1.5 N·m
76 ± 13 in-lb
11 ± 2 N·m
98 ± 17 in-lb
11 ± 2 N·m
98 ± 17 in-lb
Hydraulic unit bracket
<Rear (vehicles with 7 seating capacity)>
8
8
9
10
9
10
8.5 ± 1.5 N·m
76 ± 13 in-lb
11 ± 2 N·m
98 ± 17 in-lb
11 ± 2 N·m
98 ± 17 in-lb
8.5 ± 1.5 N·m
76 ± 13 in-lb
6
6
WHEEL SPEED SENSOR
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-191
NOTE: The vehicle speed detection encoder is inte-
grated with the front wheel bearing and the rear hub
assembly, which cannot be disassembled.
INSTALLATION SERVICE POINTS
.
>>A<< REAR WHEEL SPEED SENSOR, O-RING,
AND BOLT (CONNECTION OF REAR WHEEL
SPEED SENSOR WITH REAR WHEEL HUB
ASSEMBLY) INSTALLATION <VEHICLES WITH 5
SEATING CAPACITY>
1. Align the mounting bolt hole position of rear wheel speed
sensor with the mounting bolt hole position of rear wheel
hub assembly.
CAUTION
• Do not insert the rear wheel speed sensor at an angle
or by prying the sensor because it may be possible that
the O-ring of rear wheel speed sensor cannot be
mounted properly.
• After the insertion, do not perform an alignment of
mounting bolt hole positions by rotating the rear wheel
speed sensor.
2. As shown in the figure, mount the rear wheel speed sensor
while keeping the sensor perpendicular to the rear wheel
hub assembly.
.
Front wheel speed sensor
removal steps
1.
Bolt (front wheel speed sensor and
knuckle connection)
2.
Front wheel speed sensor
connector
>>
C
<< 3.
Front wheel speed sensor grommet
4.
Front wheel speed sensor
>>
B
<< 5.
Harness clip
Rear wheel speed sensor
removal steps
>>
A
<< 6.
Bolt (rear wheel speed sensor and
rear wheel hub assembly
connection)
>>
A
<< 7.
O-ring
8.
Rear wheel speed sensor
connector
>>
C
<< 9.
Rear wheel speed sensor grommet
>>
A
<< 10. Rear wheel speed sensor
11. Protector
AC807126AD
O ring
Rear wheel
hub assembly
Rear wheel
speed sensor
WHEEL SPEED SENSOR
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-192
>>B<< HARNESS CLIP INSTALLATION
Install the front wheel speed sensor to the harness clip as
shown in the figure.
.
>>C<< FRONT WHEEL SPEED SENSOR
GROMMET/REAR WHEEL SPEED SENSOR
GROMMET INSTALLATION
Install the front wheel speed sensor grommet and the rear
wheel speed sensor grommet to the body panel snugly as
shown in the figure.
AC608814AB
A
A
Wheel speed sensor
Marking
Harness clip
Wheel speed sensor harness
Section A - A
AC608809
<Front>
<Rear>
AB
Front wheel speed
sensor grommet
Body panel
Body panel
Rear wheel speed
sensor grommet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст