Mitsubishi Outlander GS45X. Manual — part 762
ON-VEHICLE SERVICE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-871
MULTIPORT FUEL INJECTION (MFI) RELAY
CONTINUITY CHECK
M1131050001401
Inspect the MFI relay for continuity in accordance with the chart
shown below.
BATTERY
VOLTAGE
TERMINAL NO.
TO BE
CONNECTED
TO BATTERY
TERMINAL NO.
TO BE
CONDUCTED
Not supplied
−
1
− 3
Supplied
1
− 3
2
− 4
AK703719
1
3
2
4
1
3
2
4
AB
MFI relay side connector
MFI relay
side connector
ON-VEHICLE SERVICE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-872
FUEL PUMP RELAY CONTINUITY CHECK
M1131033001453
Inspect the fuel pump relay for continuity in accordance with
the chart shown below.
BATTERY
VOLTAGE
TERMINAL
NO. TO BE
CONNECTED
TO BATTERY
TERMINAL NO. TO
BE CONDUCTED
Supplied
6 (Connector
"A")
− 11
(Connector
"B")
1 (Connector "C")
−
1 (Connector "D")
AK604483AB
ETACS-ECU
Connector “B”
Connector “D”
Connector “C”
Connector “A”
1 2 3 4
5 6 7
8 9 10 11
131415
12
1 2
1 2
1
6
4
5
9
8
10 11
13
15
14
12
16
7
2 3
AK704078 AB
ETACS-ECU side connector
Connector “D”
Connector “C”
Connector “B”
Connector “A”
ON-VEHICLE SERVICE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-873
INJECTOR RELAY CONTINUITY CHECK
M1131054600231
Inspect the Injector relay and throttle actuator control motor
relay for continuity in accordance with the chart shown below.
THROTTLE ACTUATOR CONTROL MOTOR
RELAY CONTINUITY CHECK
M1131054900016
Inspect the Injector relay and throttle actuator control motor
relay for continuity in accordance with the chart shown below.
BATTERY
VOLTAGE
TERMINAL NO.
TO BE
CONNECTED
TO BATTERY
TERMINAL NO.
TO BE
CONDUCTED
Not supplied
−
1
− 2
Supplied
1
− 2
3
− 4
AK703720
1
2
3
4
1
2
3
4
AB
Injector relay
side connector
Injector relay
side connector
BATTERY
VOLTAGE
TERMINAL NO.
TO BE
CONNECTED
TO BATTERY
TERMINAL NO.
TO BE
CONDUCTED
Not supplied
−
1
− 2
Supplied
1
− 2
3
− 4
AK703720
1
2
3
4
1
2
3
4
AC
Throttle actuator
control motor relay
side connector
Throttle actuator
control motor relay
side connector
ON-VEHICLE SERVICE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-874
INTAKE AIR TEMPERATURE SENSOR CHECK
M1131002801635
1. Disconnect the mass airflow sensor connectors.
2. Measure resistance between terminal No. 1 and No. 4.
Standard value:
13
− 17 kΩ [at -20°C (-4°F)]
5.3
− 6.7 kΩ [at 0°C (32°F)]
2.3
− 3.0 kΩ [at 20°C (68°F)]
1.0
− 1.5 kΩ [at 40°C (104°F)]
0.56
− 0.76 kΩ [at 60°C (140°F)]
0.30
− 0.45 kΩ [at 80°C (176°F)]
3. If not within specifications, replace the mass airflow sensor.
4. Measure resistance while heating the sensor using a hair
dryer.
Normal condition:
5. If resistance does not decrease as heat increases, replace
the mass airflow sensor.
ENGINE COOLANT TEMPERATURE SENSOR
CHECK
M1131003101640
Required Special Tools:
• MB992042: Engine coolant temperature sensor wrench
CAUTION
Be careful not to touch the connector (resin section) with
the tool when removing and installing.
1. Drain engine coolant, then remove the engine coolant
temperature sensor using the special tool MB992042
(engine coolant temperature sensor wrench).
TEMPERATURE
RESISTANCE (k
Ω)
Higher
Smaller
1
2
3 4
AK604486AB
Intake air temperature
sensor connector
AK604487AB
Intake air
temperature
sensor
AK503116 AC
MB992042
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст