Mitsubishi Outlander GS45X. Manual — part 1406
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-119
CAUTION
Do not insert a probe into the terminal from D-13 interme-
diate connector front side directly, as the connector con-
tact pressure may be weakened.
(5) Check for continuity between the following terminals. It
should be less than 2 ohms.
• SRS-ECU connector C-27 (terminal No.41) and the
intermediate connector D-13 (terminal No.1)
• SRS-ECU connector C-27 (terminal No.42) and the
intermediate connector D-13 (terminal No.2)
Q: Does continuity exist?
YES : Go to Step 6.
NO : Repair the wiring harness between the C-27 harness
side connector terminal No. 41, 42 and the D-13
intermediate connector (floor harness side) terminal
No. 1, 2.
AC709326
C-27 Harness side
connector (front view)
D-13 Intermediate connector
(Curtain air bag harness side)
(rear view)
AD
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-120
STEP 5. Resistance measurement at the D-13 intermediate
connector terminal No. 1, 2 and the D-109 curtain air bag
module harness side connector terminal No. 1, 2.
(1) Disconnect the negative battery terminal.
DANGER
To prevent the air bag from deploying unintentionally,
disconnect the curtain air bag module connector
D-109 to short the squib circuit.
(2) Disconnect curtain air bag module (LH) D-109. Use a
flat-tipped screwdriver to unlock the locking button at the
harness side connector by withdrawing it toward you in two
stages, and then disconnect the connector.
(3) Disconnect the D-13 intermediate connector, unlock the
connector by sliding the locking button to the direction of the
arrow as shown in the figure, and then disconnect the
connector.
(4) Because the short spring is installed to the D-13
intermediate connector (curtain air bag harness side), insert
a cable tie [3 mm (0.12 inch) wide, 0.5 mm (0.02 inch) thick]
between terminals 1, 2 and the short spring to release the
short spring.
(5) Connect special tool MB991884 to the removed D-109
harness side connector.
AC701573
Locking
button
Flat-tipped screwdriver
Inflator
Curtain air bag wiring
harness side connector
AB
AC706606
AH
Locking button
Intermediate
connector
AC700119
D-13 Intermediate
connector (module side )
22 mm or more
Cable tie
Short spring
AK
AC201287
AC201287
MB991884
D-109
Harness side
connector
DE
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-121
CAUTION
Do not insert a probe into the terminal from D-13 interme-
diate connector front side directly, as the connector con-
tact pressure may be weakened.
(6) Check for continuity between the following terminals. It
should be less than 2 ohms.
• Intermediate connector D-13 (terminal No.1) and resis-
tor harness connector terminal No.2)
• Intermediate connector D-13 (terminal No.2) and resis-
tor harness connector terminal No.1)
Q: Is the check result normal?
YES : Replace the curtain air bag module (squib) (Refer to
).
NO : Repair the wiring harness.
STEP 6. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC B1B1A set?
YES : Replace SRS-ECU. (Refer to
.)
NO : Intermittent Malfunction (Refer to GROUP 00, How to
Use Troubleshooting/Inspection Service Points
− How
to Cope with Intermittent Malfunction
).
AC709326
Resistor
harness
connector
D-13 Intermediate connector
(Curtain air bag harness side)
(rear view)
AE
ZC501967
AC404789
AC701411AB
MB991824
MB991827
MB991910
Data link
connector
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-122
DTC B1B1B: Curtain Air Bag Module (LH) (Squib) System (Short Circuit between Squib Circuit
Terminals)
CAUTION
If DTC B1B1B is set in the SRS-ECU, always diag-
nose the CAN main bus line.
.
CIRCUIT OPERATION
• The SRS-ECU judges how severe a collision is
by detecting signals from the side impact sensors
installed on the lower side of the center pillar and
at the quarter panel inner. If the impact is over a
predetermined level, the SRS-ECU sends an
ignition signal. At this time, if the side collision
safing G-sensor is on, the SRS air bag will inflate.
CURTAIN AIR BAG
MODULE
(SQUIB) (LH)
SRS-ECU
AC709440
Curtain Air Bag Module (Squib) (LH) Circuit
NOTE
*: CONNECTOR LOCK SWITCH
CONNECTOR COUPLED: ON
CONNECTOR UNCOUPLED: OFF
AB
AC901076
C-27 (Y)
AC
Connector: C-27
AC901080AB
Connectors: D-13, D-109
D-109 (B)
D-13 (Y)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст