Mitsubishi Outlander GS45X. Manual — part 1496
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-479
7. Place the tire to which the inflator is fixed onto the two
stacked tires. Then, place 1 or more old tires without wheel
onto the stacked tires, and tie and fix all the tires with rope.
(4 positions)
WARNING
•
Before operation, check carefully to be sure that
no one is nearby.
•
The inflator will be quite hot immediately following
the deployment, so wait at least 30 minutes to
allow it to cool before attempting to handle it.
Although not poisonous, do not inhale gas from
air bag deployment. See Deployed Air Bag Module
and Operated Seat Belt Pre-tensioner Disposal
(Refer to
instructions.
•
If the air bag fails to deploy, do not go near the
module.
8. At a location as far away from the air bag module as
possible, and from a shielded position, disconnect the two
connected wires from each other, and connect them to the
two terminals of the battery (which has been removed from
the vehicle) to deploy the air bag.
9. Discard the deployed air bag module as specified in
Deployed Air Bag Module and Seat Belt Pre-tensioner
Disposal (Refer to
.
ACX00611 AC
Old tires
without wheels
Deployment wires
ACX01315 AD
Deployment wires
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-480
DEPLOYMENT OUTSIDE THE VEHICLE <SEAT
BELT PRE-TENSIONER AND LAP
PRE-TENSIONER>
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cables before doing any further work (Refer to
).
WARNING
•
Battery posts, terminals and related accessories
contain lead and lead compounds. WASH HANDS
AFTER HANDLING.
•
Operate the seat belt pre-tensioner in a wide, flat
area at least 6 meters (20 feet) away from obsta-
cles and other people.
•
Do not perform operation outside if a strong wind
is blowing. If there is a slight breeze, place the seat
belt pre-tensioner downwind from the battery.
1. Disconnect the negative (
−) and positive (+) battery cables
from the battery terminals, and then remove the battery from
the vehicle.
WARNING
Store the seat belt pre-tensioner on a flat surface with
its operation surface facing up. Do not place anything
on top of them.
2. Remove the seat belt pre-tensioner from the vehicle (Refer
3. Connect deployment wires, each 6 meters (20 feet) or
longer, to the two leads of special tool MB991885, and cover
the connections with insulation tape. The other ends of the
deployment wires should be connected to each other
(short-circuited), to prevent sudden unexpected operation of
the seat belt pre-tensioner.
NOTE: This prevents the unintentional activation of inflator
caused by the static or others.
4. Connect the special tool MB991885, which the deployment
wires is attached to, to the seat belt pre-tensioner connector.
<Seat belt pre-tensioner>
5. Connect the special tool MB991885, which the deployment
wires is attached to, to the lap pre-tensioner connector. <Lap
pre-tensioner>
CAUTION
The adapter harness below the wheel should be loose. If it
is too tight, the reaction when the seat belt pre-tensioner
operates could damage the adapter harness.
6. Pass the thick wires through the hole on the seat belt
pre-tensioner bracket and secure them to the front (raised
part) of the wheel in two places.
AC103480
MB991885
AJ
Connection
Deployment wires
Insulator tape
6 m (20 ft) or
longer
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-481
7. Pull the seat belt out to the outside of the tire, and then place
one tire without a wheel on top.
WARNING
•
Before operation, check carefully to be sure that
no one is nearby.
•
The inflator will be quite hot immediately following
the operation, so wait at least 30 minutes to allow
it to cool before attempting to handle it. Although
not poisonous, do not inhale gas from seat belt
pre-tensioner operation. See Deployed Air Bag
Module and Operated Seat Belt pre-tensioner Dis-
posal (Refer to
dling instructions.
•
If the seat belt pre-tensioner fails to operate, do
not go near the seat belt pre-tensioner.
8. At a location as far away from the air bag module as
possible, and from a shielded position, disconnect the two
connected wires from each other, and connect them to the
two terminals of the battery (which has been removed from
the vehicle) to operate the seat belt pre-tensioner.
9. Discard the operated seat belt pre-tensioner as specified in
Deployed Air Bag Module and Seat Belt pre-tensioner
Disposal (Refer to
DEPLOYED AIR BAG MODULE AND OPERATED
SEAT BELT PRE-TENSIONER DISPOSAL
After deployment and operation, the air bag module and seat
belt pre-tensioner should be disposed of in the same manner
as any other scrap parts, adhering to local laws and/or legisla-
tion. Observe the following precautions during air bag or seat
belt pre-tensioner disposal:
1. The inflator will be quite hot immediately following
deployment, so wait at least 30 minutes to allow it cool
before attempting to handle it.
2. Do not put water or oil on the air bag after deployment or on
the seat belt pre-tensioner after operation.
AC105388AF
Tires
without
wheels
Seat belt
Deployment
wires
AC004294 AF
Vehicle battery
Deployment wires
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-482
WARNING
If after following these precautions, any material does
get into the eyes or on the skin, immediately rinse the
affected area with a large amount of clean water. If
any irritation develops, seek medical attention.
3. There may be material on the deployed air bag module or
the operated seat belt pre-tensioner, that could irritate the
eye and/or skin. Wear gloves and safety glasses when
handling a deployed air bag module or the operated seat
belt pre-tensioner.
4. Tightly seal the air bag module and seat belt pre-tensioner in
a strong plastic bag for disposal.
5. Be sure to always wash your hands after completing this
operation.
ACX00613AL
Air bag module
Strong plastic bag
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст