Mitsubishi Outlander GS45X. Manual — part 1528
GENERAL SPECIFICATIONS
TSB Revision
FRONT SUSPENSION
33-3
GENERAL SPECIFICATIONS
M1332000200493
COIL SPRING
NOTE: * : Heavyduty suspension for FWD
SERVICE SPECIFICATIONS
M1332000301824
LUBRICANT
M1333000400047
Strut assembly
Strut assembly self-locking nut
60
± 9 N⋅m (44 ± 6 ft-lb)
Strut assembly to body connection nut
45
± 7 N⋅m (33 ± 5 ft-lb)
Strut assembly to knuckle connection nut
110
± 11 N⋅m (81 ± 8 ft-lb)
Strut assembly to stabilizer link connection nut
39
± 6 N⋅m (29 ± 4 ft-lb)
Wheel speed sensor clamp nut
13
± 2 N⋅m (115 ± 17 in-lb)
Break hose clamp nut
13
± 2 N⋅m (115 ± 17 in-lb)
Item
Specification
Item
2.4L Engine
3.0L Engine
Wire diameter mm (in.)
14 (0.6)
14 (0.6)
Average diameter mm (in.)
159 (6.3)
159 (6.3)
Free length mm (in.)
339 (13.3), 326 (12.8)*
338(13.3)
Item
Standard value
Toe-in mm (in)
1
± 2 (0.04 ± 0.08)
Camber
0
°20' ± 30' (Left/right deviation within 0°30')
Caster
2
°35' ± 30' (Left/right deviation within 0°30')
Kingpin inclination
12
°45' ± 1°30'
Lower arm ball joint breakaway torque N
⋅m (in-lb)
2.2
− 4.1 (19 − 36)
Stabilizer link ball joint turning torque N
⋅m (in-lb)
0.5
− 2.9 (4.4 − 25.7)
Item
Specified lubricant
Quantity
Lower arm ball joint
Lip portion of dust cover
Multipurpose grease SAE J310,
NLGI No.2 or equivalent
As required
Inside of dust cover
9.0
± 1.0g (0.32 ±
0.04oz)
FRONT SUSPENSION DIAGNOSIS
TSB Revision
FRONT SUSPENSION
33-4
FRONT SUSPENSION DIAGNOSIS
INTRODUCTION TO FRONT SUSPENSION DIAGNOSIS
M1332009000344
If the front suspension is faulty, the vehicle will not
run straightforward or noise will occur. Incorrect
wheel alignment, malfunction of strut assembly, sta-
bilizer bar, coil spring, or worn or out-of-balance tires
can cause these problems.
FRONT SUSPENSION DIAGNOSIS TROUBLESHOOTING STRATEGY
M1332009100330
Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
front suspension fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find and repair the malfunction by following the
Symptom Chart and Symptom Procedures.
4. Verify malfunction is eliminated.
SYMPTOM CHART
M1332009400375
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Steering Wheel Is Heavy, Vibrates or Pulls to One Side
DIAGNOSIS
STEP 1. Check the tires.
Refer to GROUP 31, Diagnosis
Q: Are the tires in normal condition?
YES :
Replace the tires as necessary, then go to
Step 2.
NO :
If out of balance, balance the tires as
necessary. If excessively worn, replace the
tires as necessary and go to Step 5.
STEP 2. Check the wheel alignment.
Refer to
Q: Is the wheel alignment correct?
YES :
Go to Step 3.
NO :
Adjust it (Refer to
), then go to Step 5.
STEP 3. Check the lower arm ball joint.
Q: Is the ball joint in good condition?
YES :
Go to Step 4.
NO :
Replace the lower arm assembly (Refer to
), then go to Step 5 .
STEP 4. Check the coil spring.
Q: Is the coil spring in good condition?
YES :
Go to Step 5.
NO :
), then go to
Step 5 .
STEP 5. Retest the system.
Q: Is the malfunction eliminated?
YES :
The procedure is complete.
NO :
Return to Step 1.
Symptom
Inspection procedure
Reference page
Steering wheel is heavy, vibrates or pulls to one side
1
Excessive body rolling
2
Poor ride
3
Unequal ride height
4
Noise
5
FRONT SUSPENSION DIAGNOSIS
TSB Revision
FRONT SUSPENSION
33-5
INSPECTION PROCEDURE 2: Excessive Body Rolling
DIAGNOSIS
STEP 1. Check for broken or deteriorated
stabilizer bar.
Q: Is the stabilizer bar in good condition?
YES :
Go to Step 2.
NO :
Replace it (Refer to
), then go to
Step 3.
STEP 2. Check the strut assembly for damage.
Q: Is the strut assembly in good condition?
YES :
Go to Step 3.
NO :
), then go to
Step 3.
STEP 3. Retest the system.
Q: Is the malfunction eliminated?
YES :
The procedure is complete.
NO :
Return to Step 1.
INSPECTION PROCEDURE 3: Poor Ride
DIAGNOSIS
STEP 1. Check for improper tire inflation
pressure.
Refer to GROUP 31, On-vehicle Service
− Tire Infla-
tion Pressure Check
.
Q: Is the tire inflation correct?
YES :
Go to Step 2.
NO :
Adjust it, then go to Step 4.
STEP 2. Check for broken or deteriorated coil
spring(s).
Q: Are the coil spring(s) broken or deteriorated?
YES :
Replace the coil spring(s) (Refer to
), then go to Step 4.
NO :
Go to Step 3.
STEP 3. Check for strut assembly damage.
Q: Is the strut assembly damaged?
YES :
Replace it (Refer to
), then go to
Step 4.
NO :
Go to Step 4.
STEP 4. Retest the system.
Q: Is the malfunction eliminated?
YES :
The procedure is complete.
NO :
Return to Step 1.
INSPECTION PROCEDURE 4: Unequal Ride Height
DIAGNOSIS
STEP 1. Check for broken or deteriorated coil
spring(s).
Q: Is the coil spring(s) broken or deteriorated?
YES :
Replace it (Refer to
), then go to
Step 2.
NO :
Go to Step 2.
STEP 2. Retest the system.
Q: Is the malfunction eliminated?
YES :
The procedure is complete.
NO :
Return to Step 1.
SPECIAL TOOLS
TSB Revision
FRONT SUSPENSION
33-6
INSPECTION PROCEDURE 5: Noise
DIAGNOSIS
STEP 1. Check for lack of lubrication.
Q: Is lubrication inadequate?
YES :
Lubricate it, then go to Step 5.
NO :
Go to Step 2.
STEP 2. Check the tightened parts for looseness
as well as the bushings for wear.
Q: Are the tightened parts and bushings in good
condition?
YES :
Go to Step 3.
NO :
Replace it (Refer to
), then go to
Step 5.
STEP 3. Check for broken coil spring.
Q: Is the coil spring broken?
YES :
Replace it (Refer to
), then go to
Step 5.
NO :
Go to Step 4.
STEP 4. Check for strut assembly damage.
Q: Is the strut assembly damaged?
YES :
Replace it (Refer to
), then go to
Step 5.
NO :
Go to Step 5.
STEP 5. Retest the system.
Q: Is the malfunction eliminated?
YES :
The procedure is complete.
NO :
Return to Step 1.
SPECIAL TOOLS
M1332000600952
Tool
Tool number and name
Supersession
Application
MB991004
Wheel alignment gauge
attachment
MB991004-01 or General
service tool
Wheel alignment
measurement
MB991832
Spring compressor set
A: MB991793
Spring compressor
B: MB991795
Attachment A
C: MB991794
Upper plate
D: MB991829
Arm bracket
E: MB991830
Fixture
General service tool
Front coil spring
compression
NOTE: The coil spring can
not be compressed by
following conventional
special tools.
.
•
MB991237
Spring compressor
body
•
MB991238
Arm set
MB991680
Wrench set
a. MB991681
Wrench
b. MB991682
Socket
−
Strut assembly
disassembly and
reassembly
MB991004
MB991832
A
B
C
D
E
MB991680
A
B
a
b
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст