Mitsubishi Outlander GS45X. Manual — part 1622
DIAGNOSIS
TSB Revision
CVT
23A-45
DIAGNOSTIC FUNCTION
TCM conducts fault detection by monitoring the ter-
minal voltage of the transmission fluid temperature
sensor.
• <P0712>: If transmission fluid temperature
equals or exceeds specified value, TCM judges
that transmission fluid temperature sensor has a
failure.
• <P0713>: If transmission fluid temperature is
below specified value even after test driving for
more than the specified period, the TCM judges
that the transmission fluid temperature sensor
has a failure.
.
DESCRIPTIONS OF MONITOR METHODS
<P0712>
• TCM detects the fluid temperature 180°C (356°F)
or more for 5 seconds.
.
MONITOR EXECUTION <P0712>
• Continuous
.
MONITOR EXECUTION CONDITIONS
(OTHER MONITOR AND SENSOR)
<P0712>
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• P0741: Abnormality in lockup function
• P0746: Abnormality in hydraulic control system
function
• P0841: Abnormality in line pressure sensor func-
tion
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
LOGIC FLOW CHARTS (Monitor Sequence) <P0712>
.
AC710007
START
Yes
No
Transmission fluid 180 ˚C (356 ˚F)
Yes
No
Yes
No
Good
Malfunction
END
Continuous failure for 5 sec
All secondary parameters
are in the enable condition.
DIAGNOSIS
TSB Revision
CVT
23A-46
DTC SET CONDITIONS <P0712>
Check Conditions
• Voltage of battery: 9 volts or more.
• Voltage of battery: 16 volts or less.
JUDGMENT CRITERIA
• Value of temperature of transmission fluid: 180°C
(356
°F) or more. (5 seconds)
.
OBD-II DRIVE CYCLE PATTERN <P0712>
Ignition switch : ON (start the engine and keep it for
10 seconds or more)
.
DESCRIPTIONS OF MONITOR METHODS
<P0713>
• TCM detects the fluid temperature −40°C (−40°F)
or less for 5 seconds.
.
MONITOR EXECUTION <P0713>
• Vehicle speed 10 km/h or more has been
detected during 1 drive cycle
.
MONITOR EXECUTION CONDITIONS
(OTHER MONITOR AND SENSOR)
<P0713>
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• P0741: Abnormality in lockup function
• P0746: Abnormality in hydraulic control system
function
• P0841: Abnormality in line pressure sensor func-
tion
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
DIAGNOSIS
TSB Revision
CVT
23A-47
LOGIC FLOW CHARTS (Monitor Sequence) <P0713>
.
DTC SET CONDITIONS <P0713>
Check Conditions
• After vehicle speed: 10 km/h (6.2 mph) or more.
• Voltage of battery: 9 volts or more.
• Voltage of battery: 16 volts or less.
JUDGMENT CRITERIA
• Value of temperature of transmission fluid: −40°C
(-40
°F) or less. (5 seconds)
.
OBD-II DRIVE CYCLE PATTERN <P0713>
transmission range: D (Drive the vehicle for 10 sec-
onds or more while the accelerator opening angle is
20% or more)
.
PROBABLE CAUSES
• Malfunction of the valve body assembly (Faulty
transmission fluid temperature sensor)
• Damaged wiring harness and connectors
• Malfunction of TCM
AC710008
START
Yes
No
Transmission fluid -40 ˚C (-40 ˚F)
Yes
No
Yes
No
Yes
No
Good
Malfunction
END
After vehicle speed 10 km/h (6.2 mph)
Continuous failure for 5 sec
All secondary parameters
are in the enable condition.
DIAGNOSIS
TSB Revision
CVT
23A-48
DIAGNOSTIC PROCEDURE
STEP 1. M.U.T.-III data list
Item 5: Transmission fluid temperature sensor signal (Refer to
Data List Reference Table
).
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Go to Step 2.
STEP 2. Check the following connector:
• B-125 Transaxle assembly connector
• C-37 TCM connector
• A-12 Intermediate connector
Check the terminals for a contact status problem and internal
short circuit.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Repair the defective connector.
STEP 3. Check for open circuit and short to ground in the
wiring harness between the CVT assembly connector and
the TCM connector
Between B-125 CVT assembly connector (terminal No.17) and
C-37 TCM connector (terminal No.50)
Q: Is the check result normal?
YES : Go to Step 4.
NO : Repair the wiring harness.
STEP 4. Check for open circuit in the wiring harness
between the CVT assembly connector and the TCM
connector
Between B-125 CVT assembly connector (terminal No.19) and
C-37 TCM connector (terminal No.48)
Q: Is the check result normal?
YES : Go to Step 5.
NO : Repair the wiring harness.
STEP 5. Transmission fluid temperature sensor check
Refer to
.
Q: Is the check result normal?
YES : Go to Step 6.
NO : Replace the valve body assembly.
STEP 6. Symptom recheck after erasing diagnostic trouble
code
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Replace TCM.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст