Mitsubishi Outlander GS45X. Manual — part 127
MMCS
TSB Revision
CHASSIS ELECTRICAL
54A-505
STEP 17. Check the wiring harness between multivision
display connector C-10 (terminal 6) and audio amplifier
connector D-126 (terminal 34)
NOTE: Also check intermediate connectors C-15 and C-22 for
loose, corroded, or damaged terminals, or terminals pushed
back in the connector. If intermediate connector C-15 or C-22 is
damaged, repair or replace the connector as described in
GROUP 00E, Harness Connector Inspection
• Check the communication line for open circuit and short cir-
cuit.
Q: Is the wiring harness between multivision display
connector C-10 (terminal 6) and audio amplifier
connector D-126 (terminal 34) in good condition?
YES : Go to Step 18.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary.
STEP 18. Retest the system
Check that the audio sound is output.
Q: Is the check result normal?
YES : The trouble can be an intermittent malfunction (Refer
to GROUP 00
− How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Go to step 19.
STEP 19. Retest the system
Temporarily replace the multivision display and check if the
sound is output.
Q: Is the check result normal?
YES : Replace the multivision display.
NO : Replace the audio amplifier.
MMCS
TSB Revision
CHASSIS ELECTRICAL
54A-506
Inspection Procedure 3: No sound is heard from one of the speakers. <Vehicles without audio
amplifier>
CAUTION
Before replacing the multivision display, ensure that the power supply circuit, the ground circuit, and
the communication circuit are normal. (Check that the voltage is 10 V or more.)
Speaker System Circuit
TWEETER (RH)
MULTIVISION DISPLAY
REAR DOOR SPEAKER (LH)
REAR DOOR SPEAKER (RH)
FRONT DOOR
SPEAKER (RH)
FRONT DOOR
SPEAKER (LH)
TWEETER (LH)
MMCS
TSB Revision
CHASSIS ELECTRICAL
54A-507
.
COMMENTS ON TROUBLE SYMPTOM
If the sound is not heard from one of the speakers,
the speaker, multivision display, communication line
from the multivision display to the speaker may have
a problem. Also, the option coding information may
be inconsistent.
.
PROBABLE CAUSES
• Malfunction of speaker
• Malfunctions of multivision display
• Option coding information inconsistency
• Damaged harness wires and connectors
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB992006: Extra Fine Probe
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
AC703148 AL
Connectors: C-10, C-17, C-20, C-112, C-113
C-20
C-113 (BR)
C-17
C-10
C-112
AC702815 AN
Connectors: C-32, C-126, C-127
C-127 (BR)
C-126
C-32
AC702817 AO
Connector: D-21
ACA02660AD
Connector: D-36
AC703415AC
Connectors: E-02, E-04, E-10, E-14, E-17, E-24
E-02 (B)
E-14 (B)
E-17
E-24
E-10
E-04
MMCS
TSB Revision
CHASSIS ELECTRICAL
54A-508
STEP 1. Check the ETACS-ECU coding data.
Use scan tool MB991958 to diagnose the CAN bus lines.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
."
(2) Turn the ignition switch to "ON" position.
(3) Operate the scan tool MB991958 to read the ETACS-ECU
option coding information (Refer to GROUP 00, Coding
Table
(4) Check that the "Number of speaker" is set to "6 speakers".
Q: Is the check result normal?
YES : Go to Step 2.
NO : Operate scan tool MB991958 to set the option coding
"Number of speaker" to "6 speakers" and check the
trouble symptom.
STEP 2. Check the MMCS service mode, CAN
communication confirmation, and coding data.
(1) Display the CAN Communication Confirmation and Coding
Data of the MMCS service mode. (Refer to
(2) Check if "6 SPEAKER (2 TWEETER)" is displayed as the
number of installed speakers.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Go to Step 4.
STEP 3. Check the service data log for the MMCS service
mode.
With the service data log of MMCS service mode displayed,
check if the service data log for SP (speaker) is displayed.
(Refer to
Q: Is the service data log for SP (speaker) displayed?
YES : Go to step 4.
NO : Go to step 7.
STEP 4. Using scan tool MB991958, diagnose the CAN bus
line.
Use scan tool MB991958 to diagnose the CAN bus lines.
(1) Turn the ignition switch to "ON" position.
(2) Diagnose the CAN bus line.
Q: Is the check result normal?
YES : Go to step 5.
NO : Repair the CAN bus line.
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст