Mitsubishi Outlander GS45X. Manual — part 1041
TRIMS
TSB Revision
INTERIOR
52A-13
<<B>> DOOR TRIM CAP REMOVAL
Insert a flat-tipped (
−) screwdriver as shown in the figure to
remove the door trim cap.
.
<<C>> FRONT/REAR DOOR TRIM REMOVAL
Using a flat-tipped (
−) screwdriver as shown in the figure,
remove the inside lock cable and the inside handle cable, then
remove the door trim.
INSTALLATION SERVICE POINTS
.
>>A<< POWER WINDOW SWITCH INSTALLATION
After the power window switch is installed or replaced, perform
learning of the power window fully-closed position (Refer to
GROUP 42A
− Door Glass and Regulator
.
>>B<< FRONT DOOR SASH TRIM INSTALLATION
Install it with the clip attached as shown in the figure.
AC508380
Door trim cap
AB
Flat-tipped screwdriver
AC303180
Inside lock cable
Inside handle cable
AB
Flat-tipped
screwdriver
AC507220AB
Clip
TRIMS
TSB Revision
INTERIOR
52A-14
LIFTGATE TRIM
REMOVAL AND INSTALLATION
M1521006500470
AC506882AC
1
2
3
4
5
6
7
6
1
B
B
Section A – A
Section E – E
Section F – F
Section G – G
Section H – H
Section B – B
Section C – C
Section D – D
5
6
A
A
5
C
C
6
E
E
1
F
F
4
G
G
2
H
H
7
D
D
Claw
Claw
Claw
Claw
Clip
Clip
Clip
Clip
Claw
Removal steps
1.
Liftgate cover garnish
2.
Liftgate pull handle
3.
Liftgate trim cap
4.
Liftgate trim
5.
Liftgate upper trim
6.
Liftgate opening side trim
7.
Lower liftgate trim
Removal steps (Continued)
HEADLINING
TSB Revision
INTERIOR
52A-15
HEADLINING
REMOVAL AND INSTALLATION
M1521001401976
CAUTION
For the removal of the headlining, refer to GROUP 52B
− Service Precautions (refer to
) and
Curtain Air Bag Module (refer to
AC701312
2
3
1
1
5
5
6
6
4
AB
7
A
A
11
13
12
9
10
8
Section A – A
9
4
Clip
Claw
NOTE
(1) : Clip positions
(2) : Claw positions
11
12
Removal steps
•
Quarter trim upper, center pillar trim
upper, and front pillar trim (Refer to
•
Rear display (Refer to GROUP 54A
− Rear Display
).
1.
Assist grip
2.
Rear dome light assembly
3.
Cargo dome light assembly
•
Front dome light connector
•
Sunroof switch connector <vehicles
with sunroof>
4.
Front dome light assembly
5.
Sun visor
<<
A
>>
6.
Sun visor holder
7.
Sunroof lid inner weather strip rear
<vehicles with sunroof>
<<
B
>>
8.
Headlining
9.
Front dome light bracket
10. Luggage compartment light bracket
11. Front energy absorber roof side
box
12. Rear energy absorber roof side box
<vehicles without curtain air bag>
13. Front energy absorber roof bracket
<vehicles wit sunroof>
Removal steps (Continued)
INTERIOR MIRROR
TSB Revision
INTERIOR
52A-16
REMOVAL SERVICE POINTS
.
<<A>> SUN VISOR HOLDER REMOVAL
Insert the special tools into the sun visor holder from its left and
right sides to disengage the claws on the sun visor holder
sides.
.
<<B>> HEADLINING ASSEMBLY REMOVAL
To remove the clip, insert a vinyl cord into a clearance between
the clip and the headlining, and pass it around the clip. Then,
pull out the clip downwards while pulling the vinyl cord.
INTERIOR MIRROR
M1521002600442
REMOVAL SERVICE POINT
.
1. Disengage the claw A and lower the cover toward arrow 1
direction.
2. Push the claw B toward arrow 2 direction to unlock, and pull
out the mirror toward arrow 3 direction.
AC005512
MB990784
MB990784
AC
Sunvisor holder
AC600751AD
Clip
Headlining
Vinyl cord
AC209066
Claw B
Claw A
Cover
1
2
3
AD
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст