Mitsubishi Outlander GS45X. Manual — part 67
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-265
STEP 12. Check the wiring harness between fog light (LH)
connector A-41 or fog light (RH) connector A-51 (terminal
1) and ground.
NOTE: Also check intermediate connector A-46 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector A-46 is damaged, repair or
replace the connector as described in GROUP 00E, Harness
Connector Inspection
.
• Check the ground wires for open circuit.
Q: Is the wiring harness between fog light (LH) connector
A-41 or fog light (RH) connector A-51 (terminal 1) and
ground in good condition?
YES : Go to Step 13.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the front fog lights illuminate normally.
STEP 13. Retest the system.
Q: Does the fog lights illuminate in good condition?
YES : The trouble can be an intermittent malfunction (Refer
to GROUP 00, How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Replace the ETACS-ECU.
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-266
Inspection Procedure 2: One of the front fog lights does not illuminate.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
FOG LIGHT
RELAY
FOG LIGHT
(LH)
(RH)
AC709504
AE
Connector: A-14X <2.4L Engine>
AC702950AM
Connector: A-14X <3.0L Engine>
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-267
.
TECHNICAL DESCRIPTION (COMMENT)
When one of the fog lights does not illuminate, the wiring har-
ness connector(s), the bulb may be defective.
.
TROUBLESHOOTING HINTS
• Burned-out fog light bulb
• Damaged harness wires and connectors
DIAGNOSIS
Required Special Tools:
• MB992006: Extra fine probe
• MB991223: Harness set
STEP 1. Check fog light (LH) connector A-41, fog light (RH)
A-51 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is fog light (LH) connector A-41, fog light (RH) A-51 in
good condition?
YES : Go to Step 2.
NO : Repair the damaged parts.
STEP 2. Check the fog light bulb.
(1) Remove the fog light bulb.
(2) Verify that the fog light bulb is not damaged or burned out.
Q: Is the fog light bulb in good condition?
YES : Go to Step 3.
NO : Replace the fog light bulb. Verify that the fog lights
illuminate normally.
AC901112
Connectors: A-41, A-46, A-51
A-41 (B)
AV
A-46 (B)
A-51 (B)
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-268
Step 3. Check the ground circuit to the fog light (LH) or fog
light (RH). Measure the resistance at fog light (LH)
connector A-41 or fog light (RH) connector A-51.
(1) Disconnect the connector, and measure at the wiring
harness side.
(2) Check the resistance between the fog light connector and
ground.
• Resistance between A-41 fog light (LH) connector termi-
nal No.1 and ground
• Resistance between A-51 front fog light (RH) connector
terminal No.1 and ground
OK: The resistance should be 2
Ω or less.
Q: Is the measured resistance 2
Ω or less?
YES : Go to Step 5.
NO : Go to Step 4.
Step 4. Check the wiring harness between fog light (LH)
connector A-41 or fog light (RH) connector A-51 (terminal
1) and ground.
NOTE: Also check intermediate connector A-46 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector A-46 is damaged, repair or
replace the connector as described in GROUP 00E, Harness
Connector Inspection
.
• Check the ground wires for open circuit.
Q: Is the wiring harness between fog light (LH) connector
A-41 or fog light (RH) connector A-51 (terminal 1) and
ground in good condition?
YES : Go to Step 7.
NO : Repair the wiring harness.
STEP 5. Check fog light relay connector A-14X for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is fog light relay connector A-14X in good condition?
YES : Go to Step 6.
NO : Repair the damaged parts.
AC702818 AS
Connectors A-41, A-51
(Harness side)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст