Mitsubishi Outlander GS45X. Manual — part 1186
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-111
• When the engine speed is more than 200 r/min
• The EEPROM abnormality occurs [When the EEPROM
abnormality occurs during the transmitter registration,
delete all the transmitters stored (including the transmitters
used for the shift to the customer-programming mode), and
finish the customer-programming mode.]
KEYLESS ENTRY SYSTEM CHECK
M1427505600102
Check the keyless entry system function as described below. If
it does not work, perform troubleshooting. Refer to
.
• Operate the transmitter to check that the doors and liftgate
can be locked and unlocked.
• Operate the transmitter to check that the answerback func-
tion works in response to door and liftgate locking/unlock-
ing.
NOTE: The hazard and horn answerback setting can be
changed using the customization function. Confirm which
setting is activated before performing these checks. Refer
to
.
INSPECTION OF KEYLESS ENTRY TIMER LOCK
FUNCTION
M1427505800106
Attempt to unlock the doors and the liftgate by using the trans-
mitter. If the doors and the liftgate are not locked within 30 sec-
onds, carry out diagnosis. Note that the doors and the liftgate
will not be locked if the ignition key is inserted within the
30-second period, one of the doors or the liftgate is opened.
Refer to
.
NOTE: The operation time of the keyless entry timer lock func-
tion can be set using the customization function. Confirm the
operation time before performing the diagnosis. Refer to
.
POWER DOOR LOCKS WITH SELECTIVE
UNLOCKING INSPECTION
M1427510800016
Press the unlock button on the transmitter once to unlock only
the driver's door. Press the unlock button of the transmitter
once again within 2 seconds after the driver's door is unlocked,
and check that the front passenger's door, rear doors, and lift-
gate are unlocked. If they are not unlocked, carry out trouble-
shooting. Refer to
NOTE: Press the unlock button on the transmitter once to
unlock only the driver's door. When the unlock button of the
transmitter is pressed once again more than 2 seconds after
the driver's door is unlocked, only the driver's door is unlocked.
NOTE: The setting of the power door locks with selective
unlocking can be changed using the customization function.
Confirm which setting is activated before performing these
checks. Refer to
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-112
TIRE PRESSURE SENSOR CHECK
M1427509900019
Refer to ID codes registration procedure
.
TIRE PRESSURE SENSOR ID CHECK
M1427510000010
Refer to ID codes registration procedure
.
CUSTOMIZATION FUNCTION
M1427504500823
Using the ETACS system of scan tool MB991958,
the following functions can be programmed. The pro-
grammed information is held even when the battery
is disconnected.
Adjustment
item (scan tool
MB991958
display)
Adjustment item
Adjusting contents
(scan tool MB991958
display)
Adjusting contents
Hazard answer
back
Adjustment of the
number of keyless
hazard warning light
answer back
flashes
Lock:1, Unlock:2
LOCK: Flashes once, UNLOCK: Flashes
twice (initial condition)
Lock:1, Unlock:0
LOCK: Flashes once, UNLOCK: No flash
Lock:0, Unlock:2
LOCK: No flash, UNLOCK: Flash twice
Lock:2, Unlock:1
LOCK: Flash twice, UNLOCK: Flash once
Lock:2, Unlock:0
LOCK: Flash twice, UNLOCK: No flash
Lock:0, Unlock:1
LOCK: No flash, UNLOCK: Flash once
Lock:0, Unlock:0
Without function
Door unlock
mode
Adjustment of
power door locks
with selective
unlocking
All doors unlock
Without function: The first operation of
keyless entry system or unlock operation
by KOS unlocks all doors.
Dr door unlock
With function: The first operation of
keyless entry system or unlock operation
by KOS unlocks the driver's door only, and
the second unlock operation within 2
seconds after that unlocks all doors. (initial
condition)
Auto door
unlock
Adjustment of the
auto door unlock
function
Disabled
Without function (initial condition)
Always (P pos)
With function: Operates when the shift
lever or the selector lever is moved to the
P position.
Always(Lock pos)
With function: Operates when the ignition
switch is moved to the LOCK (OFF)
position.
Duration of horn
chirp
Horn sounding time
during horn answer
back
Short
0.01 second (initial condition)
Long
0.02 second
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-113
NOTE: *: F.A.S.T. (Free-hand Advanced Security
Transmitter)
Horn chirp by
keyless
Horn chirp by
keyless entry
system <vehicles
without auto light>
Not sound horn
No horn answerback function
Lock any time
The horn sounds when the lock button of
keyless entry transmitter is pressed once.
W lock any time
The horn sounds when the lock button of
keyless entry transmitter is pressed twice.
(initial condition)
Horn chirp by
keyless entry
system <vehicles
with auto light>
Not sound horn
No horn answerback function
Lock any time
The horn sounds when the lock button of
keyless entry transmitter is pressed once.
Lock/auto ON
During daytime, while the lighting switch is
in the AUTO position, the horn sounds
once when the lock is pressed once.
W lock any time
The horn sounds when the lock button of
keyless entry transmitter is pressed twice.
(initial condition)
Timer lock timer Timer lock period
adjustment
30 sec
30 seconds (initial condition)
60 sec
60 seconds
120 sec
120 seconds
180 sec
180 seconds
Panic alarm
switch
With/without panic
alarm function
Disable
Without function
Enable
With function (initial condition)
Adjustment
item (scan tool
MB991958
display)
Adjustment item
Adjusting contents
(scan tool MB991958
display)
Adjusting contents
WCM
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-114
WCM
REMOVAL AND INSTALLATION
M1427500800297
CAUTION
When WCM has been replaced, all key ID codes should be registered, referring to the ID code regis-
tration judgment table
INSTALLATION SERVICE POINT
.
>>A<< WCM INSTALLATION
Check that the top claw of WCM is fixed securely to the boss of
steering lock and the antenna is not floated on the key cylinder.
AC708536
AC708747
Section A-A
Section B-B
Section C-C
2
3
2
3
2
3
B
B
C
4
3
1
2
AI
A
A
C
Claw
Claw
Claw
NOTE: Claw position is symmetrical
2.0 ± 0.5 N·m
18 ± 4 in-lb
2.5 ± 0.5 N·m
22 ± 4 in-lb
Removal steps
1.
Ignition key cover
2.
Steering column upper cover
3.
Steering column lower cover
>>
A
<< 4.
WCM
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст