Mitsubishi Outlander GS45X. Manual — part 469
SPECIAL TOOLS
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-7
MD998737
Valve stem seal installer
MD998737-01
Valve stem seal
press-fitting
MD998727
Oil pan FIPG cutter
MD998727-01
Oil pan removal
MB991883
Flywheel stopper
General service
tool
Supporting the drive plate
MD998718
Crankshaft rear oil seal
installer
MD998718-01
Press-fitting the crankshaft
rear oil seal
MB991448
Bush remover and installer
base
MB991448-01
Press-fitting the crankshaft
front oil seal
MB991614
Angle gauge
−
Balancer shaft and oil pump
module bolt installation
Tool
Tool number and name
Supersession
Application
D998727
MB991883
MB991614
SPECIAL TOOLS
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-8
MB991454
Engine hanger balancer
MZ203827-01
When the engine hanger is
used: Supporting the
engine assembly during
removal and installation of
the transaxle assembly
NOTE: Special tool
MB991454 is a part of
engine hanger attachment
set MB991453.
MB991527
Hanger
Tool not available
MB991895
Engine hanger
Tool not available
MB991928
Engine hanger
a: MB991929
Joint (50)
× 2
b: MB991930
Joint (90)
× 2
c: MB991931
Joint (140)
× 2
d: MB991932
Foot (standard)
× 4
e: MB991933
Foot (short)
× 2
f: MB991934
Chain and hook assembly
Tool not available
MB991956
Engine hanger plate
−
Tool
Tool number and name
Supersession
Application
B991454
B991527
MB991895
B991928
a
b
c
d
e
f
Slide bracket (HI)
B991956
ON-VEHICLE SERVICE
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-9
ON-VEHICLE SERVICE
DRIVE BELT TENSION CHECK
M1111003103558
1. Remove the radiator condenser tank mounting bolt, and
move the radiator condenser tank to a place where it does
not interfere with the drive belt tension check (Refer to
GROUP 14
− Radiator
P.14-49
).
CAUTION
Check the drive belt tension after turning the crankshaft
clockwise one turn or more.
2. Make sure that the indicator mark on the auto-tensioner is
within the area marked with A in the illustration.
3. If the mark is out of the area A, replace the drive belt (Refer
NOTE: The drive belt tension adjustment is not necessary
as the auto-tensioner is adopted.
4. Install the radiator condenser tank to the original position
(Refer to GROUP 14
− Radiator
P.14-49
).
AUTO-TENSIONER CHECK
M1111003002343
OPERATION CHECK
Required Special Tool:
MB992278: Belt tension release wrench
1. Stop the engine from the idle state.
2. Remove the radiator condenser tank mounting bolt, and
move the radiator condenser tank to a place where it does
not interfere with the auto-tensioner check (Refer to GROUP
14
− Radiator
P.14-49
).
3. Check that the drive belt are not protruding from the pulley
width of drive belt auto-tensioner.
4. Remove the drive belt (Refer to
AC506730 AC
A
Indicator mark
Auto-tensioner
ON-VEHICLE SERVICE
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-10
WARNING
Always work from above when releasing the tension
of the auto-tensioner. When you try to gain access
from underneath the vehicle, you will experience diffi-
culty, thus causing the tool to be dropped off.
CAUTION
To work at the optimum angle, you must choose a most
suitable box-type wrench is applied to the special tool.
WARNING
Be sure to set the box-type wrench and the special
tool MB992278 to the hexagonal parts securely to pre-
vent the tool from falling off because the tension of
the auto-tensioner is high.
5. Install special tool MB992278 and a box-type wrench at the
optimum angle.
6. Check that no binding is present by turning the
auto-tensioner in the left and right directions.
7. If there are any problems in the procedure 3 or 6, replace
the auto-tensioner (Refer to
).
8. Install the drive belt (Refer to
.)
9. Install the radiator condenser tank to the original position
(Refer to GROUP 14
− Radiator
P.14-49
).
FUNCTION CHECK
The auto-tensioner can be checked whether it is in good condi-
tion by checking its tension.
.
<When the vibration frequency is measured:
Recommendation>
Required Special Tools:
• MB992080: Belt Tension Meter Set
• MB992081: Belt Tension Meter
• MB992082: Microphone Assembly
1. Check the tension of the drive belt (Refer to
AC804028
AM
Auto-tensioner
MB992278
Box-type
wrench
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст