Mitsubishi Outlander GS45X. Manual — part 1571
POWER STEERING GEAR BOX AND LINKAGE
TSB Revision
POWER STEERING
37-47
>>B<< BAND INSTALLATION
CAUTION
• Hold the rack housing, and use special tool bellows
band crimping tool (MB992209) to crimp the bellows
band securely.
• Crimp the bellows band until special tool (MB992209)
touches the stopper.
1. Use special tool boot band crimping tool (MB992209) to
crimp the bellows band.
2. Check that crimped width (A) is within the standard value.
Standard value (A): 2.4
− 2.8 mm
.
>>C<< TIE-ROD END/JAM NUT INSTALLATION
Screw in the tie-rod to the length shown in the figure, and
hand-tighten the jam nut.
NOTE: Install the steering gear and linkage to the body, adjust
the toe-in, and then tighten the jam nut to the specified torque.
AC701769
MB992209
AD
ACX01166 AC
A
AC703667
207 mm (8.1 in)
AG
Edge of bellows
assembly
Jam nut
POWER STEERING OIL PUMP ASSEMBLY
TSB Revision
POWER STEERING
37-48
POWER STEERING OIL PUMP ASSEMBLY
REMOVAL AND INSTALLATION
M1372005201978
Pre-removal operation
• Power Steering Fluid Draining (Refer to
).
• Engine Upper Cover Removal (Refer to GROUP 11A −
Camshaft
<2.4L>).
• Engine Room Side Cover (RH) Removal (Refer to
GROUP 51
− Under Cover
<3.0L>).
• Generator and Others Belt Removal (Refer to GROUP
11A
− Crankshaft Pulley
<2.4L>, GROUP 11C
−
Crankshaft Pulley
<3.0L>).
Post-installation operation
• Generator and Others Belt Installation (Refer to GROUP
11A
− Crankshaft Pulley
<2.4L>, GROUP 11C
−
Crankshaft Pulley
<3.0L>).
• Generator and Others Belt Tension Check (Refer to
GROUP 11A
− On-vehicle Service − Drive Belt Tension
<2.4L>, GROUP 11C
− On-vehicle Ser-
vice
− Generator Drive Belt Tension Check
<3.0L>).
• Engine Upper Cover Installation (Refer to GROUP 11A −
Camshaft
<2.4L>).
• Engine Room Side Cover (RH) Installation (Refer to
GROUP 51
− Under Cover
<3.0L>).
• Power Steering Fluid Refilling and Bleeding (Refer to
AC711076 AJ
8
5
1
4
6
2
7
N
9
3
57 ± 7 N·m
42 ± 5 ft-lb
13 ± 2 N·m
115 ± 17 in-lb
13 ± 2 N·m
115 ± 17 in-lb
25 ± 4 N·m
18 ± 2 ft-lb
25 ± 4 N·m
18 ± 2 ft-lb
48 ± 7 N·m
35 ± 5 ft-lb
44 ± 8 N·m
32 ± 5 ft-lb
44 ± 10 N·m
33 ± 7 ft-lb
23 ± 2 N·m
17 ± 1 ft-lb
<2.4L Engine>
Removal steps
1.
Suction hose connection
2.
Pressure switch connector
connection
3.
Clamp bolt
4.
Eye bolt
5.
Gasket
6.
Pressure hose assembly
connection
7.
Harness bracket
8.
Oil pump assembly
9.
Oil pump bracket
Removal steps (Continued)
POWER STEERING OIL PUMP ASSEMBLY
TSB Revision
POWER STEERING
37-49
REMOVAL SERVICE POINT
.
<<A>> OIL PUMP ASSEMBLY REMOVAL
When removing the oil pump assembly, remove the stabilizer
link and stabilizer bar bracket, shift the stabilizer bar to the left
of the vehicle, and then remove the assembly from the front
wheel house (right side).(Refer to GROUP 33 - Stabilizer Bar
Removal And Installation
AC705772 AF
2
6
7
8
3
4
N
13 ± 2 N·m
115 ± 17 in-lb
25 ± 4 N·m
18 ± 2 ft-lb
57 ± 7 N·m
42 ± 5 ft-lb
50 ± 7 N·m
37 ± 5 ft-lb
1
5
<3.0L Engine>
Removal steps
1.
Pressure switch connector
connection
2.
Suction hose connection
3.
Eye bolt
4.
Gasket
5.
Pressure hose assembly
connection
<<
A
>>
6.
Oil pump assembly
7.
Heat protector
8.
Power steering pump bracket
Removal steps (Continued)
AC703638AB
Oil pump assembly
Stabilizer link
Stabilizer bar
POWER STEERING OIL PUMP ASSEMBLY
TSB Revision
POWER STEERING
37-50
INSTALLATION SERVICE POINT
.
>>A<< SUCTION HOSE CONNECTION
Align the suction hose marking within the area shown in the fig-
ure and connect the suction hose.
INSPECTION
M1372005300466
• Check the drive belt for cracks.
• Check the pulley for uneven rotation.
AC607830
AF
Suction hose
Marking
Oil pump
30˚
<2.4L Engine>
AC707955
AE
<3.0L Engine>
Marking
Oil pump assembly
Suction hose
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст