Mitsubishi Outlander GS45X. Manual — part 1316
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-209
STEP 43. Check the wiring harness between joint
connector (CAN1) C-103 and ETACS-ECU connector C-301
for open circuit.
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
(1) Disconnect joint connector (CAN1) C-103 and ETACS-ECU
connector C-301, and check the wiring harness.
(2) Check the wiring harness between joint connector (CAN1)
C-103 (terminal No.6) and ETACS-ECU connector C-301
(terminal No.6)
OK: Continuity exists (2 ohms or less)
(3) Check the wiring harness between joint connector (CAN1)
C-103 (terminal No.19) and ETACS-ECU connector C-301
(terminal No.7)
OK: Continuity exists (2 ohms or less)
Q: Is the wiring harness between joint connector (CAN1)
C-103 and ETACS-ECU connector C-301 in good
condition?
YES : Go to Step 53.
NO : Repair the wiring harness between joint connector
(CAN1) C-103 and ETACS-ECU connector C-301.
AC709707 MQ
Harness side: C-103
Harness side: C-301
Test
harness
Test
harness
AC709707 MR
Harness side: C-103
Harness side: C-301
Test
harness
Test
harness
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-210
STEP 44. Using scan tool MB991958, diagnose the CAN
bus line. (checking the combination meter for internal
failure)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect combination meter connector C-03.
(2) Connect scan tool MB991958 to the data link connector.
(3) Turn the ignition switch to the "ON" position.
(4) Diagnose CAN bus lines, and check if the scan tool
MB991958 screen is as shown in the figure.
OK: The display of the scan tool MB991958 is as
shown in the figure.
Q: Does scan tool MB991958 screen correspond to the
illustration?
YES : Repair the wiring harness between joint connector
(CAN1) C-103 and combination meter connector
C-03.
NO : Check combination meter connector C-03, and repair
if necessary. If the combination meter connector is in
good condition, replace the combination meter.
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
ACA02847AD
: Red section on screen
M.U.T.
JC
JC
SAS
AWC
ABS/ASC
AT/CVT
ENGINE
ETACS
JC
F.A.S.T.
/WCM
SRS
OCM
A/C
AUDIO
MMCS
Sat Radio
METER
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-211
STEP 45. Using scan tool MB991958, diagnose the CAN
bus line. (checking the KOS-ECU for internal failure)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect KOS-ECU connector C-102.
(2) Connect scan tool MB991958 to the data link connector.
(3) Turn the ignition switch to the "ON" position.
(4) Diagnose CAN bus lines, and check if the scan tool
MB991958 screen is as shown in the figure.
OK: The display of the scan tool MB991958 is as
shown in the figure.
Q: Does scan tool MB991958 screen correspond to the
illustration?
YES : Repair the wiring harness between joint connector
(CAN1) C-103 and KOS-ECU connector C-102.
NO : Check KOS-ECU connector C-102, and repair if
necessary. If the KOS-ECU connector is in good
condition, replace the KOS-ECU.
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
ACA02847AD
: Red section on screen
M.U.T.
JC
JC
SAS
AWC
ABS/ASC
AT/CVT
ENGINE
ETACS
JC
F.A.S.T.
/WCM
SRS
OCM
A/C
AUDIO
MMCS
Sat Radio
METER
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-212
STEP 46. Using scan tool MB991958, diagnose the CAN
bus line. (checking the WCM for internal failure)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect WCM connector C-29.
(2) Connect scan tool MB991958 to the data link connector.
(3) Turn the ignition switch to the "ON" position.
(4) Diagnose CAN bus lines, and check if the scan tool
MB991958 screen is as shown in the figure.
OK: The display of the scan tool MB991958 is as
shown in the figure.
Q: Does scan tool MB991958 screen correspond to the
illustration?
YES : Repair the wiring harness between joint connector
(CAN1) C-103 and WCM connector C-29.
NO : Check WCM connector C-29, and repair if necessary.
If the WCM connector is in good condition, replace
the WCM.
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
ACA02847AD
: Red section on screen
M.U.T.
JC
JC
SAS
AWC
ABS/ASC
AT/CVT
ENGINE
ETACS
JC
F.A.S.T.
/WCM
SRS
OCM
A/C
AUDIO
MMCS
Sat Radio
METER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст