Mitsubishi Outlander GS45X. Manual — part 85
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-337
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set to the radio and CD player.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3) Check if DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the ETACS-ECU.
NO : The trouble can be an intermittent malfunction such
as a poor connection or open circuit in the CAN bus
lines between the ETACS-ECU and the radio and CD
player (Refer to GROUP 00, How to Cope with
Intermittent Malfunction
).
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set to the radio and CD player.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3) Check if DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the radio and CD player.
NO : The trouble can be an intermittent malfunction such
as a poor connection or open circuit in the CAN bus
lines between the ETACS-ECU and the radio and CD
player (Refer to GROUP 00, How to Cope with
Intermittent Malfunction
).
DTC U0151: SRS-ABG CAN timeout
CAUTION
• If DTC U0151 is set, be sure to diagnose the
CAN bus line.
• When replacing the radio and CD player,
always check that the communication circuit
is normal.
.
DIAGNOSTIC FUNCTION
If the signal from SRS-ECU cannot be received, the
radio and CD player sets DTC U0151.
.
JUDGMENT CRITERIA
With the ignition switch in the ON position, system
voltage between 10
−16 volts (data from
ETACS-ECU), power supply fuse(IOD fuse) is OK, or
odometer value is 80.5 km (50 miles) or more, and
the communication with SRS-ECU cannot be estab-
lished for 2,500 ms or more, the radio and CD player
determines that a problem has occurred.
.
TROUBLESHOOTING HINTS
• The CAN bus line may be defective
• The radio and CD player may be defective
• The SRS-ECU may be defective
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-338
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 2.
NO : Repair the CAN bus line (Refer to GROUP 54C,
).
STEP 2. Using scan tool MB991958, read the SRS-ECU
diagnostic trouble code
Check again if the DTC is set to the SRS-ECU.
Q: Is the DTC set?
YES : Troubleshoot the SRS (Refer to GROUP 52B,
Troubleshooting
).
NO : Go to Step 3.
STEP 3. Using scan tool MB991958, read the A/C-ECU
diagnostic trouble code.
Check if the DTC U0151 is set to the A/C-ECU.
Q: Is the DTC set?
YES : Go to Step 4.
NO : Go to Step 5.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-339
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set to the radio and CD player.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3) Check if DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the SRS-ECU.
NO : The trouble can be an intermittent malfunction such
as a poor connection or open circuit in the CAN bus
lines between the SRS-ECU and the radio and CD
player (Refer to GROUP 00, How to Cope with
Intermittent Malfunction
).
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set to the radio and CD player.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3) Check if DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the radio and CD player.
NO : The trouble can be an intermittent malfunction such
as a poor connection or open circuit in the CAN bus
lines between the SRS-ECU and the radio and CD
player (Refer to GROUP 00, How to Cope with
Intermittent Malfunction
).
DTC U0154: OCM (occupant classification-ECU) CAN timeout
CAUTION
If DTC U0154 is set, be sure to diagnose the CAN
bus line.
CAUTION
When replacing the radio and CD player, always
check that the communication circuit is normal.
.
DIAGNOSTIC FUNCTION
When the signals from occupant classification-ECU
cannot be received, the radio and CD player sets
DTC U0154.
.
JUDGMENT CRITERIA
With the ignition switch in the ON position, system
voltage between 10
− 16 volts (data from
ETACS-ECU), power supply fuse(IOD fuse) is OK, or
odometer value is 80.5 km (50 miles) or more, and
the communications with occupant classifica-
tion-ECU cannot be established for 2,500 ms or
more, the radio and CD player determines that a
problem has occurred.
.
TROUBLESHOOTING HINTS
• The CAN bus line may be defective.
• The radio and CD player may be defective.
• The occupant classification-ECU may be defec-
tive.
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-340
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 2.
NO : Repair the CAN bus line (Refer to GROUP 54C,
).
STEP 2. Using scan tool MB991958, read the occupant
classification-ECU diagnostic trouble code.
Check if DTC is set to the occupant classification-ECU.
Q: Is the DTC set?
YES : Troubleshoot the SRS (Refer to GROUP 52B,
).
NO : Go to Step 3.
STEP 3. Using scan tool MB991958, read the A/C-ECU
diagnostic trouble code.
Check if the DTC U0154 is set to the A/C-ECU.
Q: Is the DTC set?
YES : Go to Step 4.
NO : Go to Step 5.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст