Mitsubishi Outlander GS45X. Manual — part 38
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-149
STEP 4. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect
."
(2) Turn the ignition switch to the "ON" position.
(3) Erase the DTC.
(4) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(5) Check if DTC is set.
Q: Is the DTC set?
YES : Replace the ETACS-ECU.
NO : The procedure is complete.
DTC L0432: RLS RS Adaptation Error
.
TROUBLE JUDGMENT
When the lighting control sensor is installed with the
wrong procedure, DTC L0432 is stored by LIN.
.
TECHNICAL DESCRIPTION (COMMENT)
The lighting control sensor may have been installed
with the wrong procedure.
• Incorrect installation procedure: Connect the con-
nector before mounting the lighting control sensor
onto the optical coupler of the windshield.
• Correct installation procedure: Mount the lighting
control sensor onto the optical coupler of the
windshield. Wipe the windshield surface thor-
oughly, and check that the surface is dry. Then,
connect the connector.
.
TROUBLESHOOTING HINTS
• Lighting control sensor improperly installed
• Lighting control sensor (rain sensor) abnormal
operation
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-150
STEP 1. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
Disconnect the connector from the lighting control sensor, and
connect the connector to the lighting control sensor again.
Then, check again if the DTC is set to LIN.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect
."
(2) Disconnect the connector of lighting control sensor, and
connect it again.
NOTE: When connecting the connector, follow the correct
installation procedure.
(3) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(4) Check if DTC is set.
Q: Is the DTC set?
YES : Go to Step 2.
NO : The lighting control sensor is installed with the wrong
procedure.
STEP 2. Lighting control sensor installation surface check
Visually check the presence of scratches or air bubbles <diam-
eter of 5 mm (0.2 inch) or more> on the windshield to which the
lighting control sensor is installed. In addition, visually check
that the optical coupler is not broken and that the lighting con-
trol sensor can be installed.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Replace the windshield (Refer to GROUP 42A
−
Windshield
)
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-151
STEP 3. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
Check again if the DTC is set to LIN.
(1) Wipe the windshield surface of the lighting control sensor
section thoroughly, and check that the surface is dry. Then,
perform the lighting control sensor (rain sensor) adaptation.
<Refer to GROUP 51
− Lighting Control Sensor (Rain
Sensor) Adaptation
>.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3) Check if DTC is set.
Q: Is the DTC set?
YES : Replace the lighting control sensor.
NO : The trouble can be an intermittent malfunction (Refer
to GROUP 00
− How to use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
DTC L0434: RLS Rain Sensor Error
DTC L0436: RLS Light Sensor Error
.
TROUBLE JUDGMENT
If a trouble occurs in the lighting control sensor, DTC
L0434 and L0436 are stored to LIN.
.
TECHNICAL DESCRIPTION (COMMENT)
Malfunction of the lighting control sensor
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-152
Using scan tool MB991958, Check whether the diagnostic
trouble code is reset.
Check again if the DTC is set to LIN.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect
."
(2) Erase the DTC.
(3) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(4) Check if DTC is set.
Q: Is the DTC set?
YES : Replace the lighting control sensor.
NO : The trouble can be an intermittent malfunction (Refer
to GROUP 00
− How to use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст