Mitsubishi Outlander GS45X. Manual — part 1104
SUNROOF
TSB Revision
BODY
42A-219
INSTALLATION SERVICE POINT
.
>>A<< FRONT DRAIN PIPE/REAR DRAIN PIPE
INSTALLATION
Install the grommet, and adjust the drain pipe projection as
shown.
INSPECTION
M1426001300231
SUNROOF SWITCH CONTINUITY CHECK
AC703557AB
60 ± 5
(2.35 ± 0.15)
60 ± 5
(2.35 ± 0.15)
<Front drain pipe>
<Rear drain pipe>
Grommet
Grommet
Unit: mm (inch)
Switch
position
Terminal
number
Normal value
Tilt-up
3
− 4
Continuity exists
(2
Ω or less)
OFF
3
− 4, 4 − 5, 4 −
6
Open circuit
Open
4
− 5
Continuity exists
(2
Ω or less)
Close/tilt-down 4
− 6
Continuity exists
(2
Ω or less)
AC703554AB
Sunroof switch
SUNROOF
TSB Revision
BODY
42A-220
DISASSEMBLY AND ASSEMBLY
M1426001400528
REMOVAL SERVICE POINTS
.
<<A>> SUNROOF SUNSHADE REMOVAL
CAUTION
Before removing the sunroof sunshade, clean the shaded
area of the sunroof housing shown in the illustration. Oth-
erwise, the sunroof sunshade may get dirty when it is
removed.
.
<<B>> SUNROOF DRIP PLATE AND SUNROOF
LID SLIDE GUIDE REMOVAL
Slide the slide part of the sunroof lid slide guide to the rear of
the sunroof housing, and then pull out the sunroof drip plate
and sunroof lid slide guide.
AC708942
1
2
3
4
5
6
7
8
9
10
AB
N
Disassembly steps
1.
Sunroof drip rail
2.
Sunroof sunshade stopper
3.
Sunroof sunshade knob
<<
A
>>
4.
Sunroof sunshade
<<
B
>>
>>
B
<<
5.
Sunroof drip plate and sunroof lid
slide guide
6.
Sunroof drip plate
7.
Sunroof lid slide guide
8.
Sunroof deflector
>>
A
9.
Sunroof pad
10. Sunroof housing
Disassembly steps (Continued)
AC708959
AB
Sunroof housing
AC708960
AB
: Front of sunroof housing
Slide part
Sunroof lid slide guide
SUNROOF
TSB Revision
BODY
42A-221
INSTALLATION SERVICE POINTS
.
>>A<< SUNROOF PAD INSTALLATION
Align the sunroof pad with the mark on the sunroof housing,
and then install it.
.
>>B<< SUNROOF DRIP PLATE AND SUNROOF
LID SLIDE GUIDE INSTALLATION
1. Install the sunroof drip plate and sunroof lid slide guide to
the sunroof housing.
2. Push the sunroof drip plate and sunroof lid slide guide
toward the front of sunroof housing until they stop.
CAUTION
If the slide part of the sunroof lid slide guide is positioned
incorrectly, the sunroof may not work normally.
3. Push the slide part of the sunroof lid slide guide forward.
Align the pin center of the slide part with the location shown
in the illustration.
AC708962
AB
: Front of sunroof housing
Mark
Sunroof pad
Sunroof housing
AC708961
AB
: Front of sunroof housing
Slide part
Sunroof lid slide guide
Pin
LOOSE PANEL
TSB Revision
BODY
42A-222
LOOSE PANEL
REMOVAL AND INSTALLATION
M1421003101071
INSTALLATION SERVICE POINT
.
>>A<< HEADLIGHT SUPPORT UPPER PANEL
INSTALLATION
Install the mounting bolts of headlight support upper panel in
the order shown in the illustration.
AC900200AB
5
4
3
1
2
9.0 ± 1.0 N·m
<Headlight support upper panel>
9.0 ± 2.0 N·m
9.0 ± 2.0 N·m
9.0 ± 2.0 N·m
80 ± 17 in-lb
80 ± 17 in-lb
80 ± 17 in-lb
80 ± 8 in-lb
Headlight support upper panel
removal steps
• Headlight support panel cover (Refer
to GROUP 51
−Radiator grille
P.51-9
.)
• Front bumper (Refer to GROUP
51
−Front Bumper
P.51-4
.)
• Headlight (Refer to GROUP
54A
−Headlight
.)
1. Headlight support upper panel cover
2. Hood lock release cable
3. Hood latch
4. Air cleaner intake duct
• Front impact sensor (Refer to
GROUP 52B
− Front impact sensor
• Front harness
>>
A
<< 5. Headlight support upper panel
Headlight support upper panel
removal steps (Continued)
AC900234AB
Headlight support
upper panel
1
5
2
3
6
4
7
8
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст