Mitsubishi Outlander GS45X. Manual — part 1567
STEERING WHEEL
TSB Revision
POWER STEERING
37-31
STEERING WHEEL
REMOVAL AND INSTALLATION
M1372011401692
WARNING
•
Before removing the steering wheel and driver’s air bag module assembly, refer to
GROUP 52B, Service Precautions
and Driver’s Air Bag Module and Clock Spring
.
•
When removing and installing the steering wheel, do not let it bump against the driver’s
air bag module.
CAUTION
After the installation, perform a calibration for the ASC-ECU to learn the steering wheel sensor neutral
point. (Refer to GROUP 35C
− On-vehicle Service − Steering Wheel Sensor Calibration
<Vehicles with ASC>
Pre-removal operation
Steering wheel straight-ahead position check
Post-installation operation
• Steering wheel straight-ahead position check
• Steering wheel shake check
AC611821
1
8
8
2
3
4
1
15
14
9.5 ± 2.5 N·m
84 ± 22 in-lb
44 ± 11 N·m
32 ± 8 ft-lb
Claw
Claw
AH
13
11
7
6
2.5 ± 0.5 N·m
22 ± 4 in-lb
Claw
Claw
15
4
3
2
10
Claw
Claw
Claw
9.5 ± 2.5 N·m
84 ± 22 in-lb
5
9
12
Removal steps
<<
A
>>
1.
Cover
>>
B
<<
2.
Horn connector connection
>>
B
<<
3.
Steering switch connector
connection
<<
B
>>
>>
B
<<
4.
Driver's air bag module connector
connection
5.
Steering wheel voice control
switch connector connection
<Vehicles with steering wheel
voice control switch>
6.
Steering wheel voice control
switch cover <Vehicles with
steering wheel voice control
switch>
7.
Steering wheel voice control
switch <Vehicles with steering
wheel voice control switch>
<<
C
>>
>>
A
<<
8.
Driver's air bag module
9.
Cruise control switch connector
connection
Removal steps (Continued)
STEERING WHEEL
TSB Revision
POWER STEERING
37-32
Required Special Tools:
• MB990784: Ornament Remover
• MB990803: Steering wheel puller
REMOVAL SERVICE POINTS
.
<<A>> COVER REMOVAL
Insert the ornament remover (Special tool: MB990784) into the
notch shown in the figure, and remove the cover.
.
<<B>> DRIVER’S AIR BAG MODULE
CONNECTOR REMOVAL
Slide the outer housing of the driver’s air bag module connector
in the arrow direction shown, and disconnect the connector.
.
10. Cruise control switch
11. Bezel cover (LH) <Vehicles
without steering wheel audio
remote control switch>
12. Steering wheel audio remote
control switch connector
connection <Vehicles with
steering wheel audio remote
control switch>
Removal steps (Continued)
13. Steering wheel audio remote
control switch <Vehicles with
steering wheel audio remote
control switch>
14. Flange nut
<<
D
>>
>>
A
<<
15. Steering wheel assembly
Removal steps (Continued)
AC505865AB
MB990784
Cover
AC607302
AC600868
Outer housing of the driver's air bag
module connector
Horn connector
Lower column
cover
Driver's air bag
module connector
(4-pin, yellow)
AB
STEERING WHEEL
TSB Revision
POWER STEERING
37-33
<<C>> DRIVER’S AIR BAG MODULE ASSEMBLY
REMOVAL
WARNING
•
The air bag module must not be measured with
such equipment as an ohmmeter.
•
The air bag module must not be disassembled.
•
The removed air bag module should be stored in a
clean, dry place with the deployment surface fac-
ing up.
1. Using t-type long torx wrench (T30), a torx screw is loos-
ened completely and removed.
.
<<D>> STEERING WHEEL ASSEMBLY REMOVAL
1. Position the steering wheel in a straight ahead direction.
CAUTION
Use the special tool to remove the steering wheel since the
steering column collision absorbing mechanism may be
damaged.
Use special tool MB990803 to remove the steering wheel.
AC608854
AC609541AB
Equal to or more than
40mm (1.6 inch).
AC607307
MB990803
AB
STEERING WHEEL
TSB Revision
POWER STEERING
37-34
INSTALLATION SERVICE POINTS
.
>>A<< STEERING WHEEL ASSEMBLY/DRIVER'S
AIR BAG MODULE INSTALLATION
After centering the clock spring (Refer to GROUP 52B - Air Bag
Module Clock Spring
), install the steering wheel
assembly.
.
>>B<< DRIVER’S AIR BAG MODULE
CONNECTOR CONNECTION/STEERING SWITCH
CONNECTOR CONNECTION/HORN CONNECTOR
CONNECTION
Connect the connector securely and route the harnesses not to
lie off the cover hole.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст