Mitsubishi Outlander GS45X. Manual — part 928
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-645
DTC P1248: AWD Plausibility <AWD>
.
TECHNICAL DESCRIPTION
Checks for an abnormal signal of AWD-ECU.
.
DTC SET CONDITIONS
Check Condition
• Ignition switch is "ON" position.
Judgment Criterion
• The torque reduction requested signal from
AWD-ECU is not normal.
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• AWD system failed.
• ECM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the AWD-DTC.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the electronic control AWD-DTC set?
YES : Refer to GROUP 27C, Troubleshooting
− Diagnosis
NO : Go to Step 2 .
AK700568AB
MB991824
MB991827
MB991910
Data link
connector
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-646
STEP 2. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
(1) Turn the ignition switch to the "ON" position.
(2) After the DTC has been deleted, read the DTC again.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P1248 set?
YES : Replace the ECM. When the ECM is replaced,
register the ID code. Refer to GROUP 42B, Diagnosis
− ID Codes Registration Judgment Table <Vehicles
or GROUP 42C, Diagnosis
− ID
Codes Registration Judgment Table <Vehicles with
WCM>
NO : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
DTC P1506: Idle Control Sytem RPM Lower Than Expected at Low Temperature
.
TECHNICAL DESCRIPTION
• The amount of air taken in during idling is regu-
lated by the opening and closing of the throttle
valve.
• The ECM checks the difference between the
actual engine speed and the target engine speed.
.
DESCRIPTIONS OF MONITOR METHODS
Difference between actual and target idle speed is
over the specified value.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS
(Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Misfire monitor
• Exhaust gas recirculation (EGR) system monitor
• Fuel system monitor
Sensor (The sensor below is determined to be
normal)
• Mass airflow sensor
• Engine coolant temperature sensor
• Intake air temperature sensor
• Barometric pressure sensor
• Throttle position sensor
.
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-647
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• Under the closed loop idle speed control.
• The engine coolant temperature is between 7°C
(45
°F) and 41°C (105°F).
• Battery positive voltage is higher than 10 volts.
• Barometric pressure is higher than 76 kPa (22.4
in.Hg).
• Intake air temperature is higher than −10°C
(14
°F).
• More than 3 seconds have elapsed from the pre-
vious monitoring.
• Target air flow rate is more than 33 g/sec (28
L/sec).
Judgement Criterion
• The actual idle speed is less than the target idle
speed by 100 r/min or more for 10 seconds.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
.
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• Throttle valve area is dirty.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
Good
Malfunction
Calculated Ne
End
No
No
No
AK604345
Ne < -100 r/min
or > 200 r/min
Have 10secs passed?
Ne = (actual-Ne) - (target-Ne)
Ne: engine speed
Start
Yes
Yes
Yes
Monitoring
conditions
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-648
• MB991827: USB Cable
• MB991910: Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC)
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the diagnostic trouble code other than P0506 set?
YES : Refer to Diagnostic Trouble Code Chart
.
NO : Go to Step 2.
STEP 2. Check the throttle body. (throttle valve area)
Q: Is the throttle valve area dirty?
YES : Perform cleaning. Refer to Throttle Body (Throttle
Valve Area) Cleaning
. Then go to Step 4.
NO : Go to Step 3.
STEP 3. Replace the throttle body assembly.
(1) Replace the throttle body assembly.
(2) Carry out test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Pattern 23
(3) Check the diagnostic trouble code (DTC).
Q: Is DTC P1506 set?
YES : Replace the ECM. When the ECM is replaced,
register the ID code. Refer to GROUP 42B, Diagnosis
− ID Codes Registration Judgment Table <Vehicles
or GROUP 42C, Diagnosis
− ID
Codes Registration Judgment Table <Vehicles with
WCM>
NO : The inspection is complete.
AK700568AB
MB991824
MB991827
MB991910
Data link
connector
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст