Mitsubishi Outlander GS45X. Manual — part 168
SATELLITE RADIO TUNER
TSB Revision
CHASSIS ELECTRICAL
54A-669
DTC U0164: A/C CAN timeout
CAUTION
• If DTC U0164 is set, be sure to diagnose the
CAN bus line.
• When replacing the ECU, always check that
the communication circuit is normal.
.
DIAGNOSTIC FUNCTION
If the signal from A/C-ECU cannot be received, the
satellite radio tuner sets DTC U0164.
.
JUDGMENT CRITERIA
With the ignition switch in the ON position, system
voltage between 10
−16 volts (data from
ETACS-ECU), power supply fuse (IOD fuse) is OK,
or odometer value is 80.5 km (50 miles) or more, and
the communication with A/C-ECU cannot be estab-
lished for 2,500 ms or more, the satellite radio tuner
determines that a problem has occurred.
.
TROUBLESHOOTING HINTS
• The CAN bus line may be defective.
• The A/C-ECU may be defective.
• The satellite radio tuner may be defective.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 2.
NO : Repair the CAN bus line (Refer to GROUP 54C,
).
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
SATELLITE RADIO TUNER
TSB Revision
CHASSIS ELECTRICAL
54A-670
STEP 2. Using scan tool MB991958, read the A/C-ECU
diagnostic trouble code.
Check if DTC is set to the A/C-ECU.
Q: Is the DTC set?
YES : Troubleshoot the A/C. (Refer to GROUP 55A, Manual
A/C Diagnosis
GROUP 55B, Auto A/C
NO : Go to Step 3.
STEP 3. Using scan tool MB991958, read the ETACS
diagnostic trouble code.
Check if the DTC U0164 is set to the ETACS-ECU.
Q: Is the DTC set?
YES : Go to Step 4.
NO : Go to Step 5.
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set to the satellite radio tuner.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3) Check if DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the A/C-ECU.
NO : The trouble can be an intermittent malfunction such
as a poor connection or open circuit in the CAN bus
lines between the A/C-ECU and the satellite radio
tuner (Refer to GROUP 00, How to Cope with
Intermittent Malfunction
).
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set to the satellite radio tuner.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3) Check if DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the satellite radio tuner.
NO : The trouble can be an intermittent malfunction such
as a poor connection or open circuit in the CAN bus
lines between the A/C-ECU and the satellite radio
tuner (Refer to GROUP 00, How to Cope with
Intermittent Malfunction
).
SATELLITE RADIO TUNER
TSB Revision
CHASSIS ELECTRICAL
54A-671
DTC U0168: WCM/KOS CAN timeout
CAUTION
• If DTC U0168 is set, be sure to diagnose the
CAN bus line.
• When replacing the ECU, always check that
the communication circuit is normal.
.
DIAGNOSTIC FUNCTION
If the signal from KOS-ECU <vehicles with KOS> or
WCM <vehicles with WCM> cannot be received, the
satellite radio tuner sets DTC U0168.
.
JUDGMENT CRITERIA
With the ignition switch in the ON position, system
voltage between 10
− 16 V (data from ETACS-ECU),
power supply fuse (IOD fuse) is OK, or odometer
value is 80.5 km (50 miles) or more, and the commu-
nication with KOS-ECU <vehicles with KOS> or
WCM <vehicles with WCM> cannot be established
for 2,500 ms or more, the satellite radio tuner deter-
mines that a problem has occurred.
.
TROUBLESHOOTING HINTS
• Malfunction of CAN bus line may be defective.
• Malfunction of the KOS-ECU may be defective.
<vehicles with KOS>
• Malfunction of the WCM may be defective. <vehi-
cles with WCM>
• Malfunction of satellite radio tuner may be defec-
tive.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
SATELLITE RADIO TUNER
TSB Revision
CHASSIS ELECTRICAL
54A-672
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 2.
NO : Repair the CAN bus line (Refer to GROUP 54C,
).
STEP 2. Using scan tool MB991958, read the KOS-ECU
<vehicles with KOS> or WCM <vehicles with WCM>
diagnostic trouble code.
Check again if the DTC is set to the KOS-ECU <vehicles with
KOS> or WCM <vehicles with WCM>.
Q: Is the DTC set?
YES : Troubleshoot the KOS or WCM (Refer to GROUP
42B, Diagnosis
<KOS> or GROUP 42C,
<WCM>).
NO : Go to Step 3.
STEP 3. Using scan tool MB991958, read the diagnostic
trouble code.
Check if the DTC U0168 is set to the ETACS-ECU.
Q: Is the DTC set?
YES : Go to Step 4.
NO : Go to Step 5.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст