Mitsubishi Outlander GS45X. Manual — part 210
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-837
SYSTEM BLOCK DIAGRAM
AC900821
<"Ready to be triggered">
<Except "Ready to be triggered">
LIN cutoff control unit
LIN cutoff control unit
Theft alarm siren
Theft alarm siren
Theft alarm sensor
LIN bus line
LIN bus line
Signal line
AC
ETACS-ECU
keyless entry function or the keyless operation system
ignition switch, Door switch,
Tailgate latch switch, Hood switch
Theft alarm indicator, turn-signal lamp
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-838
SPECIAL TOOLS
M1547000600394
Tool
Tool number and
name
Supersession
Application
MB990784
Ornament remover
General service
tool
Removal of center air outlet, center
panel.
MB991958
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991914
f. MB991825
g. MB991826
M.U.T.-III sub
assembly
a. Vehicle
communication
interface (V.C.I.)
b. M.U.T.-III USB
cable
c. M.U.T.-III main
harness A
(Vehicles with
CAN
communication
system)
d. M.U.T.-III main
harness B
(Vehicles without
CAN
communication
system)
e. M.U.T.-III main
harness C (for
Chrysler models
only)
f. M.U.T.-III
measurement
adapter
g. M.U.T.-III trigger
harness
MB991824-KIT
NOTE: G:
MB991826
M.U.T.-III Trigger
Harness is not
necessary when
pushing V.C.I.
ENTER key.
CAUTION
M.U.T.-III main harness A
(MB991910) should be used.
M.U.T.-III main harness B and C
should not be used for this
vehicle.
Reading diagnostic trouble code
MB990784
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
a
b
c
d
e
f
g
DO NOT USE
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-839
DIAGNOSIS
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
M1547001200139
Refer to GROUP 00
− Contents of troubleshooting
.
DIAGNOSTIC FUNCTION
M1547001300084
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
MB991223
a. MB991219
b. MB991220
c. MB991221
d. MB991222
Harness set
a. Test harness
b. LED harness
c. LED harness
adaptor
d. Probe
General service
tool
Continuity check and voltage
measurement at harness wire or
connector.
a. Connector pin contact pressure
inspection
b. Power circuit inspection
c. Power circuit inspection
d. Commercial tester connection
MB992006
Extra fine probe
−
Continuity check and voltage
measurement at harness wire or
connector.
Tool
Tool number and
name
Supersession
Application
MB991223
a
d
c
b
DO NOT USE
BA
MB992006
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-840
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
1. Ensure that the ignition switch is at the "LOCK" (OFF)
position.
2. Start up the personal computer.
3. Connect special tool MB991827 to special tool MB991824
and the personal computer.
4. Connect special tool MB991910 to special tool MB991824.
5. Connect special tool MB991910 to the data link connector.
6. Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE: When special tool MB991824 is energized, special
tool MB991824 indicator light will be illuminated in a green
color.
7. Start the M.U.T.-III system on the personal computer.
NOTE: Disconnecting scan tool MB991958 is the reverse of the
connecting sequence, making sure that the ignition switch is at
the "LOCK" (OFF) position.
HOW TO READ AND ERASE DIAGNOSTIC
TROUBLE CODES
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
NOTE: If the battery voltage is low, diagnostic trouble codes will
not be set. Check the battery if scan tool MB991958 does not
display.
1. Connect scan tool MB991958 to the data link connector.
2. Turn the ignition switch to the "ON" position.
3. Select "System select" from the start-up screen.
4. Select "From 2006 MY" of "Model Year." When the "Vehicle
Information" is displayed, check the contents.
5. Select "ETACS" from "System List", and press the "OK"
button.
NOTE: When the "Loading Option Setup" list is displayed,
check the applicable item.
6. Select "Diagnostic Trouble Code." to read the DTC.
7. If a DTC is set, it is shown.
8. Choose "Erase DTCs" to erase the DTC.
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст