Mitsubishi Outlander GS45X. Manual — part 1119
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-55
STEP 2. Using scan tool MB991958, read the ETACS-ECU
diagnostic trouble code
Check if a coding-related DTC is set in the ETACS-ECU.
Q: Is the DTC set?
YES : Troubleshoot the ETACS. (Refer to GROUP 54A,
.)
NO : Go to Step 3.
STEP 3. Recheck for diagnostic trouble code.
Check again if the DTC is set to the WCM.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3) Check if DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace KOS-ECU and register the ID codes. (Refer
to
NO : The trouble can be an intermittent malfunction (Refer
to GROUP 00
− How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
DTC B2206: VIN code mismatch
.
DTC SET CONDITION
KOS-ECU sets DTC B2206 when chassis number
registered in it and VIN that has been transmitted on
the CAN bus do not match.
.
TECHNICAL DESCRIPTION (COMMENT)
KOS-ECU determines that the abnormality is present
when VIN registered in it and the one that has been
transmitted on the CAN bus do not match.
.
TROUBLESHOOTING HINTS
• Malfunction of KOS-ECU (KOS-ECU being regis-
tered to another vehicle)
• Malfunction of ECM (VIN registered in ECM
unmatched)
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-56
STEP 1. Check the VIN registered in the engine control
module and the VIN of the vehicle.
Check if the VIN registered in the engine control module
matches with the VIN of the vehicle.
(1) On the system selection screen of the scan tool, select
"MFI/GDI/Diesel".
(2) Select "Coding."
(3) Select "VIN Information."
(4) Compare with the VIN of the vehicle.
Q: Does the VIN of the engine control module match with
the VIN of the vehicle?
YES : Go to Step 2.
NO : Write the VIN to the engine control module. [Refer to
GROUP 00
− How to Perform Vehicle Identification
Number (VIN) Writing
]. Record VIN and go to
Step 2.
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set to the KOS-ECU.
CAUTION
To prevent damage to scan tool (MB991958), always turn
the ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool (MB991958).
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
Q: Is the DTC set?
YES : Replace KOS-ECU and register the ID codes (Refer
to
). After registering the ID codes, go to
Step 3.
NO : The procedure is complete.
STEP 3. Recheck for diagnostic trouble code.
Check again if the DTC is set to the KOS-ECU.
(1) Turn the ignition switch to the "ON" position.
(2) Check if the DTC is set.
Q: Is the DTC set?
YES : Replace the engine control module and record the
VIN [Refer to GROUP 00
− How To Perform Vehicle
Identification Number (VIN) Writing
].
NO : The procedure is complete.
ZC501967
AC404789
AC701411AB
MB991824
MB991827
MB991910
Data link
connector
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-57
DTC B2352: Antenna fail
CAUTION
When replacing the ECU, always check that the
communication circuit is normal.
.
DTC SET CONDITION
If an open circuit or short to ground occurs in the
antenna, KOS-ECU sets the DTC B2352.
.
TECHNICAL DESCRIPTION (COMMENT)
When the ignition switch is turned ON with the emer-
gency operation by the inversely-inserted keyless
operation key, KOS-ECU sends signals to the
receiver antenna module. The receiver antenna
transmits random numbers to the keyless operation
key when it receives signals from KOS-ECU. If an
open circuit or short to ground occurs on the wiring
harness between KOS-ECU and receiver antenna at
this time, KOS-ECU determines that there is a prob-
lem.
.
TROUBLESHOOTING HINTS
• Malfunction of the receiver antenna module
• Damaged wiring harness and connectors
• Malfunction of KOS-ECU
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
ACA02751
Receiver Antenna Module and KOS-ECU Circuit
KEYLESS
OPERATION
KEY
RECEIVER ANTENNA
MODULE
KOS-ECU
TRANSPONDER
KEY ID
IMMOBILIZER
ANTENNA
KEYLESS
ENTRY
RECEIVER
AB
AC702145AB
Connector: C-30, C-102
C-30
C-102
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-58
STEP 1. Check receiver antenna module connector C-30
and KOS-ECU connector C-102 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Is the receiver antenna module connector C-30 and
KOS-ECU connector C-102 in good condition?
YES : Go to Step 2.
NO : Repair the defective connector.
STEP 2. Check the wiring harness between the receiver
antenna module connector C-30 (terminal No. 1, 2) and the
KOS-ECU connector C-102 (terminal No. 12, 11).
• Check the signal lines for open circuit and short circuit.
Q: Is the wiring harness between receiver antenna module
connector C-30 (terminal No. 1, 2) and the KOS-ECU
connector C-102 (terminal No. 12, 11) in good
condition?
YES : Go to Step 3.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary.
STEP 3. Replace the receiver antenna module, and check
whether the diagnostic trouble code is reset.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect
scan too (M.U.T.-III)
(2) Erase the DTC.
(3) Turn the ignition switch from the "LOCK" (OFF) position to
the "ON" position.
(4) Check if the DTC is set.
Q: Is the DTC set?
YES : Replace KOS-ECU and register the ID codes. (Refer
to
NO : The procedure is complete.
ZC501967
AC404789
AC701411AB
MB991824
MB991827
MB991910
Data link
connector
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст