Mitsubishi Outlander GS45X. Manual — part 498
CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-29
CAMSHAFT OIL SEAL
REMOVAL AND INSTALLATION
M1112002200512
Required Special Tools:
• MB990767: Front Hub and Flange Yoke Holder
• MD998713: Camshaft Oil Seal Installer
• MD998719: Pin
• MD998777: Camshaft Oil Seal Installer Adapter
REMOVAL SERVICE POINTS
.
<<A>> CAMSHAFT SPROCKET REMOVAL
Use special tools MB990767 and MD998719 to remove the
camshaft sprocket.
.
Pre-removal and Post-installation Operation
• Timing Belt Removal and Installation (Refer to
AC703047
1
2
3
4
N
N
90 ± 10 N·m
67 ± 7 ft-lb
AB
Removal steps
<<A>>
>>B<<
1.
Left bank camshaft sprocket
<<B>>
>>A<<
2.
Camshaft oil seal
<<A>>
>>B<<
3.
Right bank camshaft sprocket
<<B>>
>>A<<
4.
Camshaft oil seal
Removal steps (Continued)
AC703052
MB990767
MD998719
AB
CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-30
<<B>> CAMSHAFT OIL SEAL REMOVAL
1. Make a notch in the oil seal lip section with a knife, etc.
CAUTION
Be careful not to damage the camshaft and the cylinder
head.
2. Cover the end of a flat-tipped screwdriver with a shop towel
and insert into the notched section of the oil seal, and pry
out the oil seal to remove it.
INSTALLATION SERVICE POINTS
.
>>A<< CAMSHAFT OIL SEAL INSTALLATION
1. Apply engine oil to the camshaft oil seal lip.
2. Use special tools MD998713 and MD998777 to press-fit the
camshaft oil seal.
.
AC703053
Lip
section
Oil seal
Camshaft
Flat-tipped
screwdriver
AB
AC703083
<Right bank>
MD998713
Oil seal
Camshaft
AB
AC703082
MD998713
MD998777
Camshaft
Oil seal
<Left bank>
AB
CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-31
>>B<< CAMSHAFT SPROCKET INSTALLATION
1. Use special tools MB990767 and MD998719 in the same
way as during removal to hold the camshaft sprocket.
2. Tighten the camshaft sprocket mounting bolt to the specified
torque.
Tightening torque: 90
± 10 N⋅m (67 ± 7 ft-lb)
AC703052
MB990767
MD998719
AB
CAMSHAFT AND VALVE STEM SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-32
CAMSHAFT AND VALVE STEM SEAL
REMOVAL AND INSTALLATION
M1112006602217
CAUTION
*Remove and assemble the marked parts in each cylinder unit.
<LEFT BANK>
AC809144
AB
Cam section and
journal section
19
Engine oil
1
2
3
4
5
7
6
9
8
10
11
12
13
14
15
16
17
18
19
20
22*
23*
24*
22*
23*
24*
25*
26*
25*
26*
11
N
N
N
N
N
N
N
N
N
21
(Engine oil)
(Engine oil)
13 ± 1 N·m
115 ± 8 in-lb
31 ± 3 N·m
23 ± 2 ft-lb
9.5 ± 2.5 N·m
84 ± 22 in-lb
8.3 ± 1.0 N·m
73 ± 8 in-lb
30 ± 3 N·m
22 ± 2 ft-lb
30 ± 3 N·m
22 ± 2 ft-lb
11 ± 1 N·m
97 ± 8 in-lb
9.5 ± 2.5 N·m
84 ± 22 in-lb
11 ± 1 N·m
97 ± 8 in-lb
23 ± 6 N·m
17 ± 4 ft-lb
22 ± 4 N·m
16 ± 2 ft-lb
90 ± 10 N·m
66 ± 7 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
Camshaft removal steps
•
Engine cover (Refer to GROUP 16,
Ignition System
− Ignition Coil
P.16-49
).
•
Timing belt (Refer to
•
Thermostat housing (Refer to
GROUP 14, Water Hose and Water
Pipe
P.14-45
).
1.
Engine oil dipstick
2.
O-ring
3.
PCV hose connection
4.
Ignition coil connector
5.
Ignition coil
>>
E
<< 6.
Rocker cover
7.
Rocker cover gasket
Camshaft removal steps
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст